Makefile.slip
2.46 KB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
# Border router Makefile for SLIP based networking
# Assumes use of SAMR21 board
# name of your application
APPLICATION = gcoap
# If no BOARD is found in the environment, use this default:
BOARD ?= samr21-xpro
# This has to be the absolute path to the RIOT base directory:
RIOTBASE ?= $(CURDIR)/../..
BOARD_INSUFFICIENT_MEMORY := chronos msb-430 msb-430h nucleo-f030 nucleo-f334 \
stm32f0discovery telosb weio wsn430-v1_3b wsn430-v1_4 \
z1
# Must read nordic_softdevice_ble package before nanocoap package. However,
# can't read it explicitly here because it is read later, as a dependency for
# the nrf52dk board.
BOARD_BLACKLIST := nrf52dk
# Redefine port, for example use 61616 for RFC 6282 UDP compression.
#GCOAP_PORT = 5683
#CFLAGS += -DGCOAP_PORT=$(GCOAP_PORT)
# Redefine request token length, max 8.
#GCOAP_TOKENLEN = 2
#CFLAGS += -DGCOAP_TOKENLEN=$(GCOAP_TOKENLEN)
# Border router requirements
ifeq (,$(SLIP_UART))
# set default (last available UART)
SLIP_UART="(UART_NUMOF-1)"
endif
ifeq (,$(SLIP_BAUDRATE))
# set default
SLIP_BAUDRATE=115200
endif
GNRC_NETIF_NUMOF := 2
INCLUDES += -I$(CURDIR)
CFLAGS += -DSLIP_UART=$(SLIP_UART)
CFLAGS += -DSLIP_BAUDRATE=$(SLIP_BAUDRATE)
USEPKG += nanocoap
# Required by nanocoap, but only due to issue #5959.
USEMODULE += posix
# Required by nanocoap to compile nanocoap_sock.
USEMODULE += gnrc_sock_udp
# Include packages that pull up and auto-init the link layer.
# NOTE: 6LoWPAN will be included if IEEE802.15.4 devices are present
USEMODULE += gnrc_netdev_default
USEMODULE += auto_init_gnrc_netif
# Specify the mandatory networking modules
USEMODULE += gcoap
# Add a routing protocol
USEMODULE += gnrc_rpl
# Border router requirements
# Include SLIP package for IP over Serial communication
USEMODULE += gnrc_slip
# Specify the mandatory networking modules for 6LoWPAN border router
USEMODULE += gnrc_sixlowpan_border_router_default
# Additional networking modules that can be dropped if not needed
USEMODULE += gnrc_icmpv6_echo
# Required by gcoap example
USEMODULE += od
USEMODULE += fmt
# Add also the shell, some shell commands
USEMODULE += shell
USEMODULE += shell_commands
USEMODULE += ps
# Comment this out to disable code in RIOT that does safety checking
# which is not needed in a production environment but helps in the
# development process:
CFLAGS += -DDEVELHELP
# Change this to 0 show compiler invocation lines by default:
QUIET ?= 1
include $(RIOTBASE)/Makefile.include