Makefile
3.71 KB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
# name of your application
APPLICATION = gnrc_border_router
# If no BOARD is found in the environment, use this default:
BOARD ?= samr21-xpro
# This has to be the absolute path to the RIOT base directory:
RIOTBASE ?= $(CURDIR)/../..
BOARD_INSUFFICIENT_MEMORY := airfy-beacon b-l072z-lrwan1 calliope-mini \
cc2650-launchpad cc2650stk maple-mini \
microbit msb-430 msb-430h nrf51dongle nrf6310 \
nucleo32-f031 nucleo32-f042 nucleo32-f303 nucleo32-l031 \
nucleo-f030 nucleo-f070 nucleo-f072 nucleo-f103 nucleo-f302 \
nucleo-f334 nucleo-l053 nucleo-l073 opencm904 pca10000 \
pca10005 spark-core stm32f0discovery telosb wsn430-v1_3b \
wsn430-v1_4 yunjia-nrf51822 z1
BOARD_BLACKLIST += mips-malta pic32-wifire pic32-clicker# No full UART available.
# use ethos (ethernet over serial) for network communication and stdio over
# UART, but not on native, as native has a tap interface towards the host.
ifeq (,$(filter native,$(BOARD)))
GNRC_NETIF_NUMOF := 2
USEMODULE += ethos gnrc_netdev
# ethos baudrate can be configured from make command
ETHOS_BAUDRATE ?= 115200
CFLAGS += -DETHOS_BAUDRATE=$(ETHOS_BAUDRATE) -DUSE_ETHOS_FOR_STDIO
FEATURES_REQUIRED += periph_uart
endif
# SLIP legacy compatibility
# Uncomment the lines below if you want to use SLIP with this example and don't
# forget to comment the lines above for ethos.
#ifeq (,$(SLIP_UART))
# set default (last available UART)
#SLIP_UART="UART_DEV(UART_NUMOF-1)"
#endif
#ifeq (,$(SLIP_BAUDRATE))
# set default
#SLIP_BAUDRATE=115200
#endif
#GNRC_NETIF_NUMOF := 2
#INCLUDES += -I$(CURDIR)
#CFLAGS += -DSLIP_UART=$(SLIP_UART)
#CFLAGS += -DSLIP_BAUDRATE=$(SLIP_BAUDRATE)
# Include SLIP package for IP over Serial communication
#USEMODULE += slipdev
# Include packages that pull up and auto-init the link layer.
# NOTE: 6LoWPAN will be included if IEEE802.15.4 devices are present
USEMODULE += gnrc_netdev_default
USEMODULE += auto_init_gnrc_netif
# Specify the mandatory networking modules for 6LoWPAN border router
USEMODULE += gnrc_sixlowpan_border_router_default
# Add forwarding table
USEMODULE += fib
# Additional networking modules that can be dropped if not needed
USEMODULE += gnrc_icmpv6_echo
# Add also the shell, some shell commands
USEMODULE += shell
USEMODULE += shell_commands
USEMODULE += ps
USEMODULE += at86rf231
# include UHCP client
USEMODULE += gnrc_uhcpc
# Comment this out to disable code in RIOT that does safety checking
# which is not needed in a production environment but helps in the
# development process:
CFLAGS += -DDEVELHELP
# Change this to 0 show compiler invocation lines by default:
QUIET ?= 1
TAP ?= tap0
IPV6_PREFIX ?= 2001:db8::/64
# We override the `make term` command to use ethos
TERMPROG ?= sudo sh $(RIOTBASE)/dist/tools/ethos/start_network.sh
TERMFLAGS ?= $(PORT) $(TAP) $(IPV6_PREFIX)
# We depend on the ethos host tools to run the border router, we build them
# if necessary
TERMDEPS += host-tools
include $(RIOTBASE)/Makefile.include
.PHONY: host-tools
host-tools:
$(Q)env -u CC -u CFLAGS make -C $(RIOTBASE)/dist/tools
# Set a custom channel if needed
ifneq (,$(filter cc110x,$(USEMODULE))) # radio is cc110x sub-GHz
DEFAULT_CHANNEL ?= 0
CFLAGS += -DCC110X_DEFAULT_CHANNEL=$(DEFAULT_CHANNEL)
else
ifneq (,$(filter at86rf212b,$(USEMODULE))) # radio is IEEE 802.15.4 sub-GHz
DEFAULT_CHANNEL ?= 5
CFLAGS += -DIEEE802154_DEFAULT_SUBGHZ_CHANNEL=$(DEFAULT_CHANNEL)
else # radio is IEEE 802.15.4 2.4 GHz
DEFAULT_CHANNEL ?= 26
CFLAGS += -DIEEE802154_DEFAULT_CHANNEL=$(DEFAULT_CHANNEL)
endif
endif