keygrbb.ino
3.23 KB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
#include <Keyboard.h>
#include <Wire.h>
#include "Adafruit_MPR121.h"
#include <string.h>
#define ti 20
#include<SD.h>
#ifndef _BV
#define _BV(bit) (1 << (bit))
#endif
// You can have up to 4 on one i2c bus but one is enough for testing!
Adafruit_MPR121 cap = Adafruit_MPR121();
// Keeps track of the last pins touched
// so we know when buttons are 'released'
uint16_t lasttouched = 0;
uint16_t currtouched = 0;
int tab[]={3,7,15,2,6,14,1,5,9,0,4,8};
File fichier;
String filename="texte.txt";
char c;
void Printstr(String msg){
Serial.println(msg);
}
void keyboardprint ( String texte ){
int i = 0;
while (texte[i]!='\0'){
if(texte[i]=='@'){
Keyboard.write('"');
}
else if(texte[i]=='"'){
Keyboard.write('@');
}
else if(texte[i]=='\\'){
Keyboard.press(KEY_RIGHT_ALT);
Keyboard.press(92);
}
else {
Keyboard.write(texte[i]);
}
delay(ti);
Keyboard.releaseAll();
i++;
}
}
void setup() {
//keyboard out
pinMode(2, INPUT_PULLUP);
Keyboard.begin();
//Serial
Serial.begin(9600);
while (!Serial) { // needed to keep leonardo/micro from starting too fast!
delay(10);
}
//SD
while(! SD.begin(4)){
delay(1000);
}
Serial.println("SD OK");
//File
while( !(fichier=SD.open(filename,FILE_WRITE)) ){
delay(1000);
}
Serial.println("file OK");
//keyboard in
Serial.println("Adafruit MPR121 Capacitive Touch sensor test");
// Default address is 0x5A, if tied to 3.3V its 0x5B
// If tied to SDA its 0x5C and if SCL then 0x5D
if (!cap.begin(0x5A)) {
Serial.println("MPR121 not found, check wiring?");
while (1);
}
Serial.println("MPR121 found!");
}
void loop() {
// Get the currently touched pads
currtouched = cap.touched();
/*
//effacement de la mémoire
if ((currtouched & _BV(2)) && !(lasttouched & _BV(2)) ) {
Serial.println("D");
//effacer ce qui est présent dans la carte SD
}*/
//récupération des entrées
if ((currtouched & _BV(5)) && !(lasttouched & _BV(5))) {
Serial.println("R");
fichier.seek(0);
while((c=fichier.read())!=-1){
Keyboard.write(c);
}
}
for (uint8_t i=0; i<12; i++) {
// it if *is* touched and *wasnt* touched before, alert!
if ((currtouched & _BV(i)) && !(lasttouched & _BV(i)) ) {
Serial.print(tab[i]); Serial.println(" touched");
c=('0'+tab[i]);
Keyboard.press(c);
}
// if it *was* touched and now *isnt*, alert!
if (!(currtouched & _BV(i)) && (lasttouched & _BV(i)) ) {
Serial.print(tab[i]); Serial.println(" released");
c=('0'+tab[i]);
Keyboard.release(c);
}
if(i==1 || i==5)i++;
}
// reset our state
lasttouched = currtouched;
// comment out this line for detailed data from the sensor!
return;
// debugging info, what
Serial.print("\t\t\t\t\t\t\t\t\t\t\t\t\t 0x"); Serial.println(cap.touched(), HEX);
Serial.print("Filt: ");
for (uint8_t i=0; i<12; i++) {
Serial.print(cap.filteredData(i)); Serial.print("\t");
}
Serial.println();
Serial.print("Base: ");
for (uint8_t i=0; i<12; i++) {
Serial.print(cap.baselineData(i)); Serial.print("\t");
}
Serial.println();
// put a delay so it isn't overwhelming
delay(100);
}
// >v< <v>