advancedsettings.ino
5.14 KB
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
/***************************************************************************
This is a library for the BME280 humidity, temperature & pressure sensor
Designed specifically to work with the Adafruit BME280 Breakout
----> http://www.adafruit.com/products/2650
These sensors use I2C or SPI to communicate, 2 or 4 pins are required
to interface. The device's I2C address is either 0x76 or 0x77.
Adafruit invests time and resources providing this open source code,
please support Adafruit andopen-source hardware by purchasing products
from Adafruit!
Written by Limor Fried & Kevin Townsend for Adafruit Industries.
BSD license, all text above must be included in any redistribution
***************************************************************************/
#include <Wire.h>
#include <SPI.h>
#include <Adafruit_Sensor.h>
#include <Adafruit_BME280.h>
#define BME_SCK 13
#define BME_MISO 12
#define BME_MOSI 11
#define BME_CS 10
#define SEALEVELPRESSURE_HPA (1013.25)
Adafruit_BME280 bme; // I2C
//Adafruit_BME280 bme(BME_CS); // hardware SPI
//Adafruit_BME280 bme(BME_CS, BME_MOSI, BME_MISO, BME_SCK); // software SPI
unsigned long delayTime;
void setup() {
Serial.begin(9600);
Serial.println(F("BME280 test"));
if (! bme.begin()) {
Serial.println("Could not find a valid BME280 sensor, check wiring!");
while (1);
}
Serial.println("-- Default Test --");
Serial.println("normal mode, 16x oversampling for all, filter off,");
Serial.println("0.5ms standby period");
delayTime = 5000;
// For more details on the following scenarious, see chapter
// 3.5 "Recommended modes of operation" in the datasheet
/*
// weather monitoring
Serial.println("-- Weather Station Scenario --");
Serial.println("forced mode, 1x temperature / 1x humidity / 1x pressure oversampling,");
Serial.println("filter off");
bme.setSampling(Adafruit_BME280::MODE_FORCED,
Adafruit_BME280::SAMPLING_X1, // temperature
Adafruit_BME280::SAMPLING_X1, // pressure
Adafruit_BME280::SAMPLING_X1, // humidity
Adafruit_BME280::FILTER_OFF );
// suggested rate is 1/60Hz (1m)
delayTime = 60000; // in milliseconds
*/
/*
// humidity sensing
Serial.println("-- Humidity Sensing Scenario --");
Serial.println("forced mode, 1x temperature / 1x humidity / 0x pressure oversampling");
Serial.println("= pressure off, filter off");
bme.setSampling(Adafruit_BME280::MODE_FORCED,
Adafruit_BME280::SAMPLING_X1, // temperature
Adafruit_BME280::SAMPLING_NONE, // pressure
Adafruit_BME280::SAMPLING_X1, // humidity
Adafruit_BME280::FILTER_OFF );
// suggested rate is 1Hz (1s)
delayTime = 1000; // in milliseconds
*/
/*
// indoor navigation
Serial.println("-- Indoor Navigation Scenario --");
Serial.println("normal mode, 16x pressure / 2x temperature / 1x humidity oversampling,");
Serial.println("0.5ms standby period, filter 16x");
bme.setSampling(Adafruit_BME280::MODE_NORMAL,
Adafruit_BME280::SAMPLING_X2, // temperature
Adafruit_BME280::SAMPLING_X16, // pressure
Adafruit_BME280::SAMPLING_X1, // humidity
Adafruit_BME280::FILTER_X16,
Adafruit_BME280::STANDBY_MS_0_5 );
// suggested rate is 25Hz
// 1 + (2 * T_ovs) + (2 * P_ovs + 0.5) + (2 * H_ovs + 0.5)
// T_ovs = 2
// P_ovs = 16
// H_ovs = 1
// = 40ms (25Hz)
// with standby time that should really be 24.16913... Hz
delayTime = 41;
/*
// gaming
Serial.println("-- Gaming Scenario --");
Serial.println("normal mode, 4x pressure / 1x temperature / 0x humidity oversampling,");
Serial.println("= humidity off, 0.5ms standby period, filter 16x");
bme.setSampling(Adafruit_BME280::MODE_NORMAL,
Adafruit_BME280::SAMPLING_X1, // temperature
Adafruit_BME280::SAMPLING_X4, // pressure
Adafruit_BME280::SAMPLING_NONE, // humidity
Adafruit_BME280::FILTER_X16,
Adafruit_BME280::STANDBY_MS_0_5 );
// Suggested rate is 83Hz
// 1 + (2 * T_ovs) + (2 * P_ovs + 0.5)
// T_ovs = 1
// P_ovs = 4
// = 11.5ms + 0.5ms standby
delayTime = 12;
*/
Serial.println();
}
void loop() {
// Only needed in forced mode! In normal mode, you can remove the next line.
bme.takeForcedMeasurement(); // has no effect in normal mode
printValues();
delay(delayTime);
}
void printValues() {
Serial.print("Temperature = ");
Serial.print(bme.readTemperature());
Serial.println(" *C");
Serial.print("Pressure = ");
Serial.print(bme.readPressure() / 100.0F);
Serial.println(" hPa");
Serial.print("Approx. Altitude = ");
Serial.print(bme.readAltitude(SEALEVELPRESSURE_HPA));
Serial.println(" m");
Serial.print("Humidity = ");
Serial.print(bme.readHumidity());
Serial.println(" %");
Serial.println();
}