659c68f6
 pifou
Recherches sur at...
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
|
/** \file
*
* This file contains special DoxyGen information for the generation of the main page and other special
* documentation pages. It is not a project source file.
*/
/** \mainpage Simon Foster's USB Serial to HD44780 LCD Project
*
* \section Sec_Compat Project Compatibility:
*
* The following list indicates what microcontrollers are compatible with this project.
*
* \li AT90USB162
*
* \section Sec_Info USB Information:
*
* The following table gives a rundown of the USB utilization of this project.
*
* <table>
* <tr>
* <td><b>USB Mode:</b></td>
* <td>Device</td>
* </tr>
* <tr>
* <td><b>USB Class:</b></td>
* <td>Communications Device Class (CDC)</td>
* </tr>
* <tr>
* <td><b>USB Subclass:</b></td>
* <td>Abstract Control Model (ACM)</td>
* </tr>
* <tr>
* <td><b>Relevant Standards:</b></td>
* <td>USBIF CDC Class Standard</td>
* </tr>
* <tr>
* <td><b>Supported USB Speeds:</b></td>
* <td>Full Speed Mode</td>
* </tr>
* </table>
*
* \section Sec_Description Project Description:
*
* Firmware for a USB Virtual Serial to HD44780 LCD controller project, by Simon Foster. This
* project connects a standard HD7780 compatible LCD controller to a PC via a virtual serial
* link, so that data supplied by the host can be written to the display. This project is
* designed to use the Minimum USB AVR board, however it can be modified to suit other hardware
* if desired.
*
* LCD Datasheet: http://www.sparkfun.com/datasheets/LCD/HD44780.pdf \n
* More Information: http://en.wikipedia.org/wiki/HD44780_Character_LCD \n
*
* Below are the connections between the AVR Minimus board and LCD.
*
* <table>
* <tr>
* <td><b>AVR Pin:</b></td>
* <td><b>HD44780 LCD Pin:</b></td>
* </tr>
* <tr>
* <td>VCC</td>
* <td>VCC</td>
* </tr>
* <tr>
* <td>GND</td>
* <td>GND</td>
* </tr>
* <tr>
* <td>PD0</td>
* <td>DB4</td>
* </tr>
* <tr>
* <td>PD1</td>
* <td>DB5</td>
* </tr>
* <tr>
* <td>PD2</td>
* <td>DB6</td>
* </tr>
* <tr>
* <td>PD3</td>
* <td>DB7</td>
* </tr>
* <tr>
* <td>PD4</td>
* <td>/RS</td>
* </tr>
* <tr>
* <td>GND</td>
* <td>/RW</td>
* </tr>
* <tr>
* <td>PD7</td>
* <td>/E</td>
* </tr>
* </table>
*
* \section Sec_Options Project Options
*
* The following defines can be found in this project, which can control the project behaviour when defined, or changed in value.
*
* <table>
* <tr>
* <td>
* None
* </td>
* </tr>
* </table>
*/
|