/* ---------------------------------------------------------------------------- * SAM Software Package License * ---------------------------------------------------------------------------- * Copyright (c) 2012, Atmel Corporation * * All rights reserved. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following condition is met: * * - Redistributions of source code must retain the above copyright notice, * this list of conditions and the disclaimer below. * * Atmel's name may not be used to endorse or promote products derived from * this software without specific prior written permission. * * DISCLAIMER: THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR * IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE * DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, * INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, * OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF * LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING * NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, * EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. * ---------------------------------------------------------------------------- */ #ifndef _SAM3XA_HSMCI_COMPONENT_ #define _SAM3XA_HSMCI_COMPONENT_ #ifdef __cplusplus extern "C" { #endif /* ============================================================================= */ /** SOFTWARE API DEFINITION FOR High Speed MultiMedia Card Interface */ /* ============================================================================= */ /** \ingroup SAM3X8E_cmsis */ /** \defgroup SAM3XA_HSMCI High Speed MultiMedia Card Interface */ /*@{*/ #if !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) /** \brief Hsmci hardware registers */ typedef struct { WoReg HSMCI_CR; /**< \brief (Hsmci Offset: 0x00) Control Register */ RwReg HSMCI_MR; /**< \brief (Hsmci Offset: 0x04) Mode Register */ RwReg HSMCI_DTOR; /**< \brief (Hsmci Offset: 0x08) Data Timeout Register */ RwReg HSMCI_SDCR; /**< \brief (Hsmci Offset: 0x0C) SD/SDIO Card Register */ RwReg HSMCI_ARGR; /**< \brief (Hsmci Offset: 0x10) Argument Register */ WoReg HSMCI_CMDR; /**< \brief (Hsmci Offset: 0x14) Command Register */ RwReg HSMCI_BLKR; /**< \brief (Hsmci Offset: 0x18) Block Register */ RwReg HSMCI_CSTOR; /**< \brief (Hsmci Offset: 0x1C) Completion Signal Timeout Register */ RoReg HSMCI_RSPR[4]; /**< \brief (Hsmci Offset: 0x20) Response Register */ RoReg HSMCI_RDR; /**< \brief (Hsmci Offset: 0x30) Receive Data Register */ WoReg HSMCI_TDR; /**< \brief (Hsmci Offset: 0x34) Transmit Data Register */ RoReg Reserved1[2]; RoReg HSMCI_SR; /**< \brief (Hsmci Offset: 0x40) Status Register */ WoReg HSMCI_IER; /**< \brief (Hsmci Offset: 0x44) Interrupt Enable Register */ WoReg HSMCI_IDR; /**< \brief (Hsmci Offset: 0x48) Interrupt Disable Register */ RoReg HSMCI_IMR; /**< \brief (Hsmci Offset: 0x4C) Interrupt Mask Register */ RwReg HSMCI_DMA; /**< \brief (Hsmci Offset: 0x50) DMA Configuration Register */ RwReg HSMCI_CFG; /**< \brief (Hsmci Offset: 0x54) Configuration Register */ RoReg Reserved2[35]; RwReg HSMCI_WPMR; /**< \brief (Hsmci Offset: 0xE4) Write Protection Mode Register */ RoReg HSMCI_WPSR; /**< \brief (Hsmci Offset: 0xE8) Write Protection Status Register */ RoReg Reserved3[69]; RwReg HSMCI_FIFO[256]; /**< \brief (Hsmci Offset: 0x200) FIFO Memory Aperture0 */ } Hsmci; #endif /* !(defined(__ASSEMBLY__) || defined(__IAR_SYSTEMS_ASM__)) */ /* -------- HSMCI_CR : (HSMCI Offset: 0x00) Control Register -------- */ #define HSMCI_CR_MCIEN (0x1u << 0) /**< \brief (HSMCI_CR) Multi-Media Interface Enable */ #define HSMCI_CR_MCIDIS (0x1u << 1) /**< \brief (HSMCI_CR) Multi-Media Interface Disable */ #define HSMCI_CR_PWSEN (0x1u << 2) /**< \brief (HSMCI_CR) Power Save Mode Enable */ #define HSMCI_CR_PWSDIS (0x1u << 3) /**< \brief (HSMCI_CR) Power Save Mode Disable */ #define HSMCI_CR_SWRST (0x1u << 7) /**< \brief (HSMCI_CR) Software Reset */ /* -------- HSMCI_MR : (HSMCI Offset: 0x04) Mode Register -------- */ #define HSMCI_MR_CLKDIV_Pos 0 #define HSMCI_MR_CLKDIV_Msk (0xffu << HSMCI_MR_CLKDIV_Pos) /**< \brief (HSMCI_MR) Clock Divider */ #define HSMCI_MR_CLKDIV(value) ((HSMCI_MR_CLKDIV_Msk & ((value) << HSMCI_MR_CLKDIV_Pos))) #define HSMCI_MR_PWSDIV_Pos 8 #define HSMCI_MR_PWSDIV_Msk (0x7u << HSMCI_MR_PWSDIV_Pos) /**< \brief (HSMCI_MR) Power Saving Divider */ #define HSMCI_MR_PWSDIV(value) ((HSMCI_MR_PWSDIV_Msk & ((value) << HSMCI_MR_PWSDIV_Pos))) #define HSMCI_MR_RDPROOF (0x1u << 11) /**< \brief (HSMCI_MR) */ #define HSMCI_MR_WRPROOF (0x1u << 12) /**< \brief (HSMCI_MR) */ #define HSMCI_MR_FBYTE (0x1u << 13) /**< \brief (HSMCI_MR) Force Byte Transfer */ #define HSMCI_MR_PADV (0x1u << 14) /**< \brief (HSMCI_MR) Padding Value */ /* -------- HSMCI_DTOR : (HSMCI Offset: 0x08) Data Timeout Register -------- */ #define HSMCI_DTOR_DTOCYC_Pos 0 #define HSMCI_DTOR_DTOCYC_Msk (0xfu << HSMCI_DTOR_DTOCYC_Pos) /**< \brief (HSMCI_DTOR) Data Timeout Cycle Number */ #define HSMCI_DTOR_DTOCYC(value) ((HSMCI_DTOR_DTOCYC_Msk & ((value) << HSMCI_DTOR_DTOCYC_Pos))) #define HSMCI_DTOR_DTOMUL_Pos 4 #define HSMCI_DTOR_DTOMUL_Msk (0x7u << HSMCI_DTOR_DTOMUL_Pos) /**< \brief (HSMCI_DTOR) Data Timeout Multiplier */ #define HSMCI_DTOR_DTOMUL_1 (0x0u << 4) /**< \brief (HSMCI_DTOR) DTOCYC */ #define HSMCI_DTOR_DTOMUL_16 (0x1u << 4) /**< \brief (HSMCI_DTOR) DTOCYC x 16 */ #define HSMCI_DTOR_DTOMUL_128 (0x2u << 4) /**< \brief (HSMCI_DTOR) DTOCYC x 128 */ #define HSMCI_DTOR_DTOMUL_256 (0x3u << 4) /**< \brief (HSMCI_DTOR) DTOCYC x 256 */ #define HSMCI_DTOR_DTOMUL_1024 (0x4u << 4) /**< \brief (HSMCI_DTOR) DTOCYC x 1024 */ #define HSMCI_DTOR_DTOMUL_4096 (0x5u << 4) /**< \brief (HSMCI_DTOR) DTOCYC x 4096 */ #define HSMCI_DTOR_DTOMUL_65536 (0x6u << 4) /**< \brief (HSMCI_DTOR) DTOCYC x 65536 */ #define HSMCI_DTOR_DTOMUL_1048576 (0x7u << 4) /**< \brief (HSMCI_DTOR) DTOCYC x 1048576 */ /* -------- HSMCI_SDCR : (HSMCI Offset: 0x0C) SD/SDIO Card Register -------- */ #define HSMCI_SDCR_SDCSEL_Pos 0 #define HSMCI_SDCR_SDCSEL_Msk (0x3u << HSMCI_SDCR_SDCSEL_Pos) /**< \brief (HSMCI_SDCR) SDCard/SDIO Slot */ #define HSMCI_SDCR_SDCSEL_SLOTA (0x0u << 0) /**< \brief (HSMCI_SDCR) Slot A is selected. */ #define HSMCI_SDCR_SDCSEL_SLOTB (0x1u << 0) /**< \brief (HSMCI_SDCR) SDCARD/SDIO Slot B selected */ #define HSMCI_SDCR_SDCSEL_SLOTC (0x2u << 0) /**< \brief (HSMCI_SDCR) - */ #define HSMCI_SDCR_SDCSEL_SLOTD (0x3u << 0) /**< \brief (HSMCI_SDCR) - */ #define HSMCI_SDCR_SDCBUS_Pos 6 #define HSMCI_SDCR_SDCBUS_Msk (0x3u << HSMCI_SDCR_SDCBUS_Pos) /**< \brief (HSMCI_SDCR) SDCard/SDIO Bus Width */ #define HSMCI_SDCR_SDCBUS_1 (0x0u << 6) /**< \brief (HSMCI_SDCR) 1 bit */ #define HSMCI_SDCR_SDCBUS_4 (0x2u << 6) /**< \brief (HSMCI_SDCR) 4 bit */ #define HSMCI_SDCR_SDCBUS_8 (0x3u << 6) /**< \brief (HSMCI_SDCR) 8 bit */ /* -------- HSMCI_ARGR : (HSMCI Offset: 0x10) Argument Register -------- */ #define HSMCI_ARGR_ARG_Pos 0 #define HSMCI_ARGR_ARG_Msk (0xffffffffu << HSMCI_ARGR_ARG_Pos) /**< \brief (HSMCI_ARGR) Command Argument */ #define HSMCI_ARGR_ARG(value) ((HSMCI_ARGR_ARG_Msk & ((value) << HSMCI_ARGR_ARG_Pos))) /* -------- HSMCI_CMDR : (HSMCI Offset: 0x14) Command Register -------- */ #define HSMCI_CMDR_CMDNB_Pos 0 #define HSMCI_CMDR_CMDNB_Msk (0x3fu << HSMCI_CMDR_CMDNB_Pos) /**< \brief (HSMCI_CMDR) Command Number */ #define HSMCI_CMDR_CMDNB(value) ((HSMCI_CMDR_CMDNB_Msk & ((value) << HSMCI_CMDR_CMDNB_Pos))) #define HSMCI_CMDR_RSPTYP_Pos 6 #define HSMCI_CMDR_RSPTYP_Msk (0x3u << HSMCI_CMDR_RSPTYP_Pos) /**< \brief (HSMCI_CMDR) Response Type */ #define HSMCI_CMDR_RSPTYP_NORESP (0x0u << 6) /**< \brief (HSMCI_CMDR) No response. */ #define HSMCI_CMDR_RSPTYP_48_BIT (0x1u << 6) /**< \brief (HSMCI_CMDR) 48-bit response. */ #define HSMCI_CMDR_RSPTYP_136_BIT (0x2u << 6) /**< \brief (HSMCI_CMDR) 136-bit response. */ #define HSMCI_CMDR_RSPTYP_R1B (0x3u << 6) /**< \brief (HSMCI_CMDR) R1b response type */ #define HSMCI_CMDR_SPCMD_Pos 8 #define HSMCI_CMDR_SPCMD_Msk (0x7u << HSMCI_CMDR_SPCMD_Pos) /**< \brief (HSMCI_CMDR) Special Command */ #define HSMCI_CMDR_SPCMD_STD (0x0u << 8) /**< \brief (HSMCI_CMDR) Not a special CMD. */ #define HSMCI_CMDR_SPCMD_INIT (0x1u << 8) /**< \brief (HSMCI_CMDR) Initialization CMD: 74 clock cycles for initialization sequence. */ #define HSMCI_CMDR_SPCMD_SYNC (0x2u << 8) /**< \brief (HSMCI_CMDR) Synchronized CMD: Wait for the end of the current data block transfer before sending the pending command. */ #define HSMCI_CMDR_SPCMD_CE_ATA (0x3u << 8) /**< \brief (HSMCI_CMDR) CE-ATA Completion Signal disable Command. The host cancels the ability for the device to return a command completion signal on the command line. */ #define HSMCI_CMDR_SPCMD_IT_CMD (0x4u << 8) /**< \brief (HSMCI_CMDR) Interrupt command: Corresponds to the Interrupt Mode (CMD40). */ #define HSMCI_CMDR_SPCMD_IT_RESP (0x5u << 8) /**< \brief (HSMCI_CMDR) Interrupt response: Corresponds to the Interrupt Mode (CMD40). */ #define HSMCI_CMDR_SPCMD_BOR (0x6u << 8) /**< \brief (HSMCI_CMDR) Boot Operation Request. Start a boot operation mode, the host processor can read boot data from the MMC device directly. */ #define HSMCI_CMDR_SPCMD_EBO (0x7u << 8) /**< \brief (HSMCI_CMDR) End Boot Operation. This command allows the host processor to terminate the boot operation mode. */ #define HSMCI_CMDR_OPDCMD (0x1u << 11) /**< \brief (HSMCI_CMDR) Open Drain Command */ #define HSMCI_CMDR_OPDCMD_PUSHPULL (0x0u << 11) /**< \brief (HSMCI_CMDR) Push pull command. */ #define HSMCI_CMDR_OPDCMD_OPENDRAIN (0x1u << 11) /**< \brief (HSMCI_CMDR) Open drain command. */ #define HSMCI_CMDR_MAXLAT (0x1u << 12) /**< \brief (HSMCI_CMDR) Max Latency for Command to Response */ #define HSMCI_CMDR_MAXLAT_5 (0x0u << 12) /**< \brief (HSMCI_CMDR) 5-cycle max latency. */ #define HSMCI_CMDR_MAXLAT_64 (0x1u << 12) /**< \brief (HSMCI_CMDR) 64-cycle max latency. */ #define HSMCI_CMDR_TRCMD_Pos 16 #define HSMCI_CMDR_TRCMD_Msk (0x3u << HSMCI_CMDR_TRCMD_Pos) /**< \brief (HSMCI_CMDR) Transfer Command */ #define HSMCI_CMDR_TRCMD_NO_DATA (0x0u << 16) /**< \brief (HSMCI_CMDR) No data transfer */ #define HSMCI_CMDR_TRCMD_START_DATA (0x1u << 16) /**< \brief (HSMCI_CMDR) Start data transfer */ #define HSMCI_CMDR_TRCMD_STOP_DATA (0x2u << 16) /**< \brief (HSMCI_CMDR) Stop data transfer */ #define HSMCI_CMDR_TRDIR (0x1u << 18) /**< \brief (HSMCI_CMDR) Transfer Direction */ #define HSMCI_CMDR_TRDIR_WRITE (0x0u << 18) /**< \brief (HSMCI_CMDR) Write. */ #define HSMCI_CMDR_TRDIR_READ (0x1u << 18) /**< \brief (HSMCI_CMDR) Read. */ #define HSMCI_CMDR_TRTYP_Pos 19 #define HSMCI_CMDR_TRTYP_Msk (0x7u << HSMCI_CMDR_TRTYP_Pos) /**< \brief (HSMCI_CMDR) Transfer Type */ #define HSMCI_CMDR_TRTYP_SINGLE (0x0u << 19) /**< \brief (HSMCI_CMDR) MMC/SDCard Single Block */ #define HSMCI_CMDR_TRTYP_MULTIPLE (0x1u << 19) /**< \brief (HSMCI_CMDR) MMC/SDCard Multiple Block */ #define HSMCI_CMDR_TRTYP_STREAM (0x2u << 19) /**< \brief (HSMCI_CMDR) MMC Stream */ #define HSMCI_CMDR_TRTYP_BYTE (0x4u << 19) /**< \brief (HSMCI_CMDR) SDIO Byte */ #define HSMCI_CMDR_TRTYP_BLOCK (0x5u << 19) /**< \brief (HSMCI_CMDR) SDIO Block */ #define HSMCI_CMDR_IOSPCMD_Pos 24 #define HSMCI_CMDR_IOSPCMD_Msk (0x3u << HSMCI_CMDR_IOSPCMD_Pos) /**< \brief (HSMCI_CMDR) SDIO Special Command */ #define HSMCI_CMDR_IOSPCMD_STD (0x0u << 24) /**< \brief (HSMCI_CMDR) Not an SDIO Special Command */ #define HSMCI_CMDR_IOSPCMD_SUSPEND (0x1u << 24) /**< \brief (HSMCI_CMDR) SDIO Suspend Command */ #define HSMCI_CMDR_IOSPCMD_RESUME (0x2u << 24) /**< \brief (HSMCI_CMDR) SDIO Resume Command */ #define HSMCI_CMDR_ATACS (0x1u << 26) /**< \brief (HSMCI_CMDR) ATA with Command Completion Signal */ #define HSMCI_CMDR_ATACS_NORMAL (0x0u << 26) /**< \brief (HSMCI_CMDR) Normal operation mode. */ #define HSMCI_CMDR_ATACS_COMPLETION (0x1u << 26) /**< \brief (HSMCI_CMDR) This bit indicates that a completion signal is expected within a programmed amount of time (HSMCI_CSTOR). */ #define HSMCI_CMDR_BOOT_ACK (0x1u << 27) /**< \brief (HSMCI_CMDR) Boot Operation Acknowledge. */ /* -------- HSMCI_BLKR : (HSMCI Offset: 0x18) Block Register -------- */ #define HSMCI_BLKR_BCNT_Pos 0 #define HSMCI_BLKR_BCNT_Msk (0xffffu << HSMCI_BLKR_BCNT_Pos) /**< \brief (HSMCI_BLKR) MMC/SDIO Block Count - SDIO Byte Count */ #define HSMCI_BLKR_BCNT_MULTIPLE (0x0u << 0) /**< \brief (HSMCI_BLKR) MMC/SDCARD Multiple BlockFrom 1 to 65635: Value 0 corresponds to an infinite block transfer. */ #define HSMCI_BLKR_BCNT_BYTE (0x4u << 0) /**< \brief (HSMCI_BLKR) SDIO ByteFrom 1 to 512 bytes: Value 0 corresponds to a 512-byte transfer.Values from 0x200 to 0xFFFF are forbidden. */ #define HSMCI_BLKR_BCNT_BLOCK (0x5u << 0) /**< \brief (HSMCI_BLKR) SDIO BlockFrom 1 to 511 blocks: Value 0 corresponds to an infinite block transfer.Values from 0x200 to 0xFFFF are forbidden. */ #define HSMCI_BLKR_BLKLEN_Pos 16 #define HSMCI_BLKR_BLKLEN_Msk (0xffffu << HSMCI_BLKR_BLKLEN_Pos) /**< \brief (HSMCI_BLKR) Data Block Length */ #define HSMCI_BLKR_BLKLEN(value) ((HSMCI_BLKR_BLKLEN_Msk & ((value) << HSMCI_BLKR_BLKLEN_Pos))) /* -------- HSMCI_CSTOR : (HSMCI Offset: 0x1C) Completion Signal Timeout Register -------- */ #define HSMCI_CSTOR_CSTOCYC_Pos 0 #define HSMCI_CSTOR_CSTOCYC_Msk (0xfu << HSMCI_CSTOR_CSTOCYC_Pos) /**< \brief (HSMCI_CSTOR) Completion Signal Timeout Cycle Number */ #define HSMCI_CSTOR_CSTOCYC(value) ((HSMCI_CSTOR_CSTOCYC_Msk & ((value) << HSMCI_CSTOR_CSTOCYC_Pos))) #define HSMCI_CSTOR_CSTOMUL_Pos 4 #define HSMCI_CSTOR_CSTOMUL_Msk (0x7u << HSMCI_CSTOR_CSTOMUL_Pos) /**< \brief (HSMCI_CSTOR) Completion Signal Timeout Multiplier */ #define HSMCI_CSTOR_CSTOMUL_1 (0x0u << 4) /**< \brief (HSMCI_CSTOR) CSTOCYC x 1 */ #define HSMCI_CSTOR_CSTOMUL_16 (0x1u << 4) /**< \brief (HSMCI_CSTOR) CSTOCYC x 16 */ #define HSMCI_CSTOR_CSTOMUL_128 (0x2u << 4) /**< \brief (HSMCI_CSTOR) CSTOCYC x 128 */ #define HSMCI_CSTOR_CSTOMUL_256 (0x3u << 4) /**< \brief (HSMCI_CSTOR) CSTOCYC x 256 */ #define HSMCI_CSTOR_CSTOMUL_1024 (0x4u << 4) /**< \brief (HSMCI_CSTOR) CSTOCYC x 1024 */ #define HSMCI_CSTOR_CSTOMUL_4096 (0x5u << 4) /**< \brief (HSMCI_CSTOR) CSTOCYC x 4096 */ #define HSMCI_CSTOR_CSTOMUL_65536 (0x6u << 4) /**< \brief (HSMCI_CSTOR) CSTOCYC x 65536 */ #define HSMCI_CSTOR_CSTOMUL_1048576 (0x7u << 4) /**< \brief (HSMCI_CSTOR) CSTOCYC x 1048576 */ /* -------- HSMCI_RSPR[4] : (HSMCI Offset: 0x20) Response Register -------- */ #define HSMCI_RSPR_RSP_Pos 0 #define HSMCI_RSPR_RSP_Msk (0xffffffffu << HSMCI_RSPR_RSP_Pos) /**< \brief (HSMCI_RSPR[4]) Response */ /* -------- HSMCI_RDR : (HSMCI Offset: 0x30) Receive Data Register -------- */ #define HSMCI_RDR_DATA_Pos 0 #define HSMCI_RDR_DATA_Msk (0xffffffffu << HSMCI_RDR_DATA_Pos) /**< \brief (HSMCI_RDR) Data to Read */ /* -------- HSMCI_TDR : (HSMCI Offset: 0x34) Transmit Data Register -------- */ #define HSMCI_TDR_DATA_Pos 0 #define HSMCI_TDR_DATA_Msk (0xffffffffu << HSMCI_TDR_DATA_Pos) /**< \brief (HSMCI_TDR) Data to Write */ #define HSMCI_TDR_DATA(value) ((HSMCI_TDR_DATA_Msk & ((value) << HSMCI_TDR_DATA_Pos))) /* -------- HSMCI_SR : (HSMCI Offset: 0x40) Status Register -------- */ #define HSMCI_SR_CMDRDY (0x1u << 0) /**< \brief (HSMCI_SR) Command Ready */ #define HSMCI_SR_RXRDY (0x1u << 1) /**< \brief (HSMCI_SR) Receiver Ready */ #define HSMCI_SR_TXRDY (0x1u << 2) /**< \brief (HSMCI_SR) Transmit Ready */ #define HSMCI_SR_BLKE (0x1u << 3) /**< \brief (HSMCI_SR) Data Block Ended */ #define HSMCI_SR_DTIP (0x1u << 4) /**< \brief (HSMCI_SR) Data Transfer in Progress */ #define HSMCI_SR_NOTBUSY (0x1u << 5) /**< \brief (HSMCI_SR) HSMCI Not Busy */ #define HSMCI_SR_SDIOIRQforSlotA (0x1u << 8) /**< \brief (HSMCI_SR) */ #define HSMCI_SR_SDIOIRQforSlotB (0x1u << 9) /**< \brief (HSMCI_SR) */ #define HSMCI_SR_SDIOWAIT (0x1u << 12) /**< \brief (HSMCI_SR) SDIO Read Wait Operation Status */ #define HSMCI_SR_CSRCV (0x1u << 13) /**< \brief (HSMCI_SR) CE-ATA Completion Signal Received */ #define HSMCI_SR_RINDE (0x1u << 16) /**< \brief (HSMCI_SR) Response Index Error */ #define HSMCI_SR_RDIRE (0x1u << 17) /**< \brief (HSMCI_SR) Response Direction Error */ #define HSMCI_SR_RCRCE (0x1u << 18) /**< \brief (HSMCI_SR) Response CRC Error */ #define HSMCI_SR_RENDE (0x1u << 19) /**< \brief (HSMCI_SR) Response End Bit Error */ #define HSMCI_SR_RTOE (0x1u << 20) /**< \brief (HSMCI_SR) Response Time-out Error */ #define HSMCI_SR_DCRCE (0x1u << 21) /**< \brief (HSMCI_SR) Data CRC Error */ #define HSMCI_SR_DTOE (0x1u << 22) /**< \brief (HSMCI_SR) Data Time-out Error */ #define HSMCI_SR_CSTOE (0x1u << 23) /**< \brief (HSMCI_SR) Completion Signal Time-out Error */ #define HSMCI_SR_BLKOVRE (0x1u << 24) /**< \brief (HSMCI_SR) DMA Block Overrun Error */ #define HSMCI_SR_DMADONE (0x1u << 25) /**< \brief (HSMCI_SR) DMA Transfer done */ #define HSMCI_SR_FIFOEMPTY (0x1u << 26) /**< \brief (HSMCI_SR) FIFO empty flag */ #define HSMCI_SR_XFRDONE (0x1u << 27) /**< \brief (HSMCI_SR) Transfer Done flag */ #define HSMCI_SR_ACKRCV (0x1u << 28) /**< \brief (HSMCI_SR) Boot Operation Acknowledge Received */ #define HSMCI_SR_ACKRCVE (0x1u << 29) /**< \brief (HSMCI_SR) Boot Operation Acknowledge Error */ #define HSMCI_SR_OVRE (0x1u << 30) /**< \brief (HSMCI_SR) Overrun */ #define HSMCI_SR_UNRE (0x1u << 31) /**< \brief (HSMCI_SR) Underrun */ /* -------- HSMCI_IER : (HSMCI Offset: 0x44) Interrupt Enable Register -------- */ #define HSMCI_IER_CMDRDY (0x1u << 0) /**< \brief (HSMCI_IER) Command Ready Interrupt Enable */ #define HSMCI_IER_RXRDY (0x1u << 1) /**< \brief (HSMCI_IER) Receiver Ready Interrupt Enable */ #define HSMCI_IER_TXRDY (0x1u << 2) /**< \brief (HSMCI_IER) Transmit Ready Interrupt Enable */ #define HSMCI_IER_BLKE (0x1u << 3) /**< \brief (HSMCI_IER) Data Block Ended Interrupt Enable */ #define HSMCI_IER_DTIP (0x1u << 4) /**< \brief (HSMCI_IER) Data Transfer in Progress Interrupt Enable */ #define HSMCI_IER_NOTBUSY (0x1u << 5) /**< \brief (HSMCI_IER) Data Not Busy Interrupt Enable */ #define HSMCI_IER_SDIOIRQforSlotA (0x1u << 8) /**< \brief (HSMCI_IER) */ #define HSMCI_IER_SDIOIRQforSlotB (0x1u << 9) /**< \brief (HSMCI_IER) */ #define HSMCI_IER_SDIOWAIT (0x1u << 12) /**< \brief (HSMCI_IER) SDIO Read Wait Operation Status Interrupt Enable */ #define HSMCI_IER_CSRCV (0x1u << 13) /**< \brief (HSMCI_IER) Completion Signal Received Interrupt Enable */ #define HSMCI_IER_RINDE (0x1u << 16) /**< \brief (HSMCI_IER) Response Index Error Interrupt Enable */ #define HSMCI_IER_RDIRE (0x1u << 17) /**< \brief (HSMCI_IER) Response Direction Error Interrupt Enable */ #define HSMCI_IER_RCRCE (0x1u << 18) /**< \brief (HSMCI_IER) Response CRC Error Interrupt Enable */ #define HSMCI_IER_RENDE (0x1u << 19) /**< \brief (HSMCI_IER) Response End Bit Error Interrupt Enable */ #define HSMCI_IER_RTOE (0x1u << 20) /**< \brief (HSMCI_IER) Response Time-out Error Interrupt Enable */ #define HSMCI_IER_DCRCE (0x1u << 21) /**< \brief (HSMCI_IER) Data CRC Error Interrupt Enable */ #define HSMCI_IER_DTOE (0x1u << 22) /**< \brief (HSMCI_IER) Data Time-out Error Interrupt Enable */ #define HSMCI_IER_CSTOE (0x1u << 23) /**< \brief (HSMCI_IER) Completion Signal Timeout Error Interrupt Enable */ #define HSMCI_IER_BLKOVRE (0x1u << 24) /**< \brief (HSMCI_IER) DMA Block Overrun Error Interrupt Enable */ #define HSMCI_IER_DMADONE (0x1u << 25) /**< \brief (HSMCI_IER) DMA Transfer completed Interrupt Enable */ #define HSMCI_IER_FIFOEMPTY (0x1u << 26) /**< \brief (HSMCI_IER) FIFO empty Interrupt enable */ #define HSMCI_IER_XFRDONE (0x1u << 27) /**< \brief (HSMCI_IER) Transfer Done Interrupt enable */ #define HSMCI_IER_ACKRCV (0x1u << 28) /**< \brief (HSMCI_IER) Boot Acknowledge Interrupt Enable */ #define HSMCI_IER_ACKRCVE (0x1u << 29) /**< \brief (HSMCI_IER) Boot Acknowledge Error Interrupt Enable */ #define HSMCI_IER_OVRE (0x1u << 30) /**< \brief (HSMCI_IER) Overrun Interrupt Enable */ #define HSMCI_IER_UNRE (0x1u << 31) /**< \brief (HSMCI_IER) Underrun Interrupt Enable */ /* -------- HSMCI_IDR : (HSMCI Offset: 0x48) Interrupt Disable Register -------- */ #define HSMCI_IDR_CMDRDY (0x1u << 0) /**< \brief (HSMCI_IDR) Command Ready Interrupt Disable */ #define HSMCI_IDR_RXRDY (0x1u << 1) /**< \brief (HSMCI_IDR) Receiver Ready Interrupt Disable */ #define HSMCI_IDR_TXRDY (0x1u << 2) /**< \brief (HSMCI_IDR) Transmit Ready Interrupt Disable */ #define HSMCI_IDR_BLKE (0x1u << 3) /**< \brief (HSMCI_IDR) Data Block Ended Interrupt Disable */ #define HSMCI_IDR_DTIP (0x1u << 4) /**< \brief (HSMCI_IDR) Data Transfer in Progress Interrupt Disable */ #define HSMCI_IDR_NOTBUSY (0x1u << 5) /**< \brief (HSMCI_IDR) Data Not Busy Interrupt Disable */ #define HSMCI_IDR_SDIOIRQforSlotA (0x1u << 8) /**< \brief (HSMCI_IDR) */ #define HSMCI_IDR_SDIOIRQforSlotB (0x1u << 9) /**< \brief (HSMCI_IDR) */ #define HSMCI_IDR_SDIOWAIT (0x1u << 12) /**< \brief (HSMCI_IDR) SDIO Read Wait Operation Status Interrupt Disable */ #define HSMCI_IDR_CSRCV (0x1u << 13) /**< \brief (HSMCI_IDR) Completion Signal received interrupt Disable */ #define HSMCI_IDR_RINDE (0x1u << 16) /**< \brief (HSMCI_IDR) Response Index Error Interrupt Disable */ #define HSMCI_IDR_RDIRE (0x1u << 17) /**< \brief (HSMCI_IDR) Response Direction Error Interrupt Disable */ #define HSMCI_IDR_RCRCE (0x1u << 18) /**< \brief (HSMCI_IDR) Response CRC Error Interrupt Disable */ #define HSMCI_IDR_RENDE (0x1u << 19) /**< \brief (HSMCI_IDR) Response End Bit Error Interrupt Disable */ #define HSMCI_IDR_RTOE (0x1u << 20) /**< \brief (HSMCI_IDR) Response Time-out Error Interrupt Disable */ #define HSMCI_IDR_DCRCE (0x1u << 21) /**< \brief (HSMCI_IDR) Data CRC Error Interrupt Disable */ #define HSMCI_IDR_DTOE (0x1u << 22) /**< \brief (HSMCI_IDR) Data Time-out Error Interrupt Disable */ #define HSMCI_IDR_CSTOE (0x1u << 23) /**< \brief (HSMCI_IDR) Completion Signal Time out Error Interrupt Disable */ #define HSMCI_IDR_BLKOVRE (0x1u << 24) /**< \brief (HSMCI_IDR) DMA Block Overrun Error Interrupt Disable */ #define HSMCI_IDR_DMADONE (0x1u << 25) /**< \brief (HSMCI_IDR) DMA Transfer completed Interrupt Disable */ #define HSMCI_IDR_FIFOEMPTY (0x1u << 26) /**< \brief (HSMCI_IDR) FIFO empty Interrupt Disable */ #define HSMCI_IDR_XFRDONE (0x1u << 27) /**< \brief (HSMCI_IDR) Transfer Done Interrupt Disable */ #define HSMCI_IDR_ACKRCV (0x1u << 28) /**< \brief (HSMCI_IDR) Boot Acknowledge Interrupt Disable */ #define HSMCI_IDR_ACKRCVE (0x1u << 29) /**< \brief (HSMCI_IDR) Boot Acknowledge Error Interrupt Disable */ #define HSMCI_IDR_OVRE (0x1u << 30) /**< \brief (HSMCI_IDR) Overrun Interrupt Disable */ #define HSMCI_IDR_UNRE (0x1u << 31) /**< \brief (HSMCI_IDR) Underrun Interrupt Disable */ /* -------- HSMCI_IMR : (HSMCI Offset: 0x4C) Interrupt Mask Register -------- */ #define HSMCI_IMR_CMDRDY (0x1u << 0) /**< \brief (HSMCI_IMR) Command Ready Interrupt Mask */ #define HSMCI_IMR_RXRDY (0x1u << 1) /**< \brief (HSMCI_IMR) Receiver Ready Interrupt Mask */ #define HSMCI_IMR_TXRDY (0x1u << 2) /**< \brief (HSMCI_IMR) Transmit Ready Interrupt Mask */ #define HSMCI_IMR_BLKE (0x1u << 3) /**< \brief (HSMCI_IMR) Data Block Ended Interrupt Mask */ #define HSMCI_IMR_DTIP (0x1u << 4) /**< \brief (HSMCI_IMR) Data Transfer in Progress Interrupt Mask */ #define HSMCI_IMR_NOTBUSY (0x1u << 5) /**< \brief (HSMCI_IMR) Data Not Busy Interrupt Mask */ #define HSMCI_IMR_SDIOIRQforSlotA (0x1u << 8) /**< \brief (HSMCI_IMR) */ #define HSMCI_IMR_SDIOIRQforSlotB (0x1u << 9) /**< \brief (HSMCI_IMR) */ #define HSMCI_IMR_SDIOWAIT (0x1u << 12) /**< \brief (HSMCI_IMR) SDIO Read Wait Operation Status Interrupt Mask */ #define HSMCI_IMR_CSRCV (0x1u << 13) /**< \brief (HSMCI_IMR) Completion Signal Received Interrupt Mask */ #define HSMCI_IMR_RINDE (0x1u << 16) /**< \brief (HSMCI_IMR) Response Index Error Interrupt Mask */ #define HSMCI_IMR_RDIRE (0x1u << 17) /**< \brief (HSMCI_IMR) Response Direction Error Interrupt Mask */ #define HSMCI_IMR_RCRCE (0x1u << 18) /**< \brief (HSMCI_IMR) Response CRC Error Interrupt Mask */ #define HSMCI_IMR_RENDE (0x1u << 19) /**< \brief (HSMCI_IMR) Response End Bit Error Interrupt Mask */ #define HSMCI_IMR_RTOE (0x1u << 20) /**< \brief (HSMCI_IMR) Response Time-out Error Interrupt Mask */ #define HSMCI_IMR_DCRCE (0x1u << 21) /**< \brief (HSMCI_IMR) Data CRC Error Interrupt Mask */ #define HSMCI_IMR_DTOE (0x1u << 22) /**< \brief (HSMCI_IMR) Data Time-out Error Interrupt Mask */ #define HSMCI_IMR_CSTOE (0x1u << 23) /**< \brief (HSMCI_IMR) Completion Signal Time-out Error Interrupt Mask */ #define HSMCI_IMR_BLKOVRE (0x1u << 24) /**< \brief (HSMCI_IMR) DMA Block Overrun Error Interrupt Mask */ #define HSMCI_IMR_DMADONE (0x1u << 25) /**< \brief (HSMCI_IMR) DMA Transfer Completed Interrupt Mask */ #define HSMCI_IMR_FIFOEMPTY (0x1u << 26) /**< \brief (HSMCI_IMR) FIFO Empty Interrupt Mask */ #define HSMCI_IMR_XFRDONE (0x1u << 27) /**< \brief (HSMCI_IMR) Transfer Done Interrupt Mask */ #define HSMCI_IMR_ACKRCV (0x1u << 28) /**< \brief (HSMCI_IMR) Boot Operation Acknowledge Received Interrupt Mask */ #define HSMCI_IMR_ACKRCVE (0x1u << 29) /**< \brief (HSMCI_IMR) Boot Operation Acknowledge Error Interrupt Mask */ #define HSMCI_IMR_OVRE (0x1u << 30) /**< \brief (HSMCI_IMR) Overrun Interrupt Mask */ #define HSMCI_IMR_UNRE (0x1u << 31) /**< \brief (HSMCI_IMR) Underrun Interrupt Mask */ /* -------- HSMCI_DMA : (HSMCI Offset: 0x50) DMA Configuration Register -------- */ #define HSMCI_DMA_OFFSET_Pos 0 #define HSMCI_DMA_OFFSET_Msk (0x3u << HSMCI_DMA_OFFSET_Pos) /**< \brief (HSMCI_DMA) DMA Write Buffer Offset */ #define HSMCI_DMA_OFFSET(value) ((HSMCI_DMA_OFFSET_Msk & ((value) << HSMCI_DMA_OFFSET_Pos))) #define HSMCI_DMA_CHKSIZE (0x1u << 4) /**< \brief (HSMCI_DMA) DMA Channel Read and Write Chunk Size */ #define HSMCI_DMA_CHKSIZE_1 (0x0u << 4) /**< \brief (HSMCI_DMA) 1 data available */ #define HSMCI_DMA_CHKSIZE_4 (0x1u << 4) /**< \brief (HSMCI_DMA) 4 data available */ #define HSMCI_DMA_DMAEN (0x1u << 8) /**< \brief (HSMCI_DMA) DMA Hardware Handshaking Enable */ #define HSMCI_DMA_ROPT (0x1u << 12) /**< \brief (HSMCI_DMA) Read Optimization with padding */ /* -------- HSMCI_CFG : (HSMCI Offset: 0x54) Configuration Register -------- */ #define HSMCI_CFG_FIFOMODE (0x1u << 0) /**< \brief (HSMCI_CFG) HSMCI Internal FIFO control mode */ #define HSMCI_CFG_FERRCTRL (0x1u << 4) /**< \brief (HSMCI_CFG) Flow Error flag reset control mode */ #define HSMCI_CFG_HSMODE (0x1u << 8) /**< \brief (HSMCI_CFG) High Speed Mode */ #define HSMCI_CFG_LSYNC (0x1u << 12) /**< \brief (HSMCI_CFG) Synchronize on the last block */ /* -------- HSMCI_WPMR : (HSMCI Offset: 0xE4) Write Protection Mode Register -------- */ #define HSMCI_WPMR_WP_EN (0x1u << 0) /**< \brief (HSMCI_WPMR) Write Protection Enable */ #define HSMCI_WPMR_WP_KEY_Pos 8 #define HSMCI_WPMR_WP_KEY_Msk (0xffffffu << HSMCI_WPMR_WP_KEY_Pos) /**< \brief (HSMCI_WPMR) Write Protection Key password */ #define HSMCI_WPMR_WP_KEY(value) ((HSMCI_WPMR_WP_KEY_Msk & ((value) << HSMCI_WPMR_WP_KEY_Pos))) /* -------- HSMCI_WPSR : (HSMCI Offset: 0xE8) Write Protection Status Register -------- */ #define HSMCI_WPSR_WP_VS_Pos 0 #define HSMCI_WPSR_WP_VS_Msk (0xfu << HSMCI_WPSR_WP_VS_Pos) /**< \brief (HSMCI_WPSR) Write Protection Violation Status */ #define HSMCI_WPSR_WP_VS_NONE (0x0u << 0) /**< \brief (HSMCI_WPSR) No Write Protection Violation occurred since the last read of this register (WP_SR) */ #define HSMCI_WPSR_WP_VS_WRITE (0x1u << 0) /**< \brief (HSMCI_WPSR) Write Protection detected unauthorized attempt to write a control register had occurred (since the last read.) */ #define HSMCI_WPSR_WP_VS_RESET (0x2u << 0) /**< \brief (HSMCI_WPSR) Software reset had been performed while Write Protection was enabled (since the last read). */ #define HSMCI_WPSR_WP_VS_BOTH (0x3u << 0) /**< \brief (HSMCI_WPSR) Both Write Protection violation and software reset with Write Protection enabled have occurred since the last read. */ #define HSMCI_WPSR_WP_VSRC_Pos 8 #define HSMCI_WPSR_WP_VSRC_Msk (0xffffu << HSMCI_WPSR_WP_VSRC_Pos) /**< \brief (HSMCI_WPSR) Write Protection Violation SouRCe */ /* -------- HSMCI_FIFO[256] : (HSMCI Offset: 0x200) FIFO Memory Aperture0 -------- */ #define HSMCI_FIFO_DATA_Pos 0 #define HSMCI_FIFO_DATA_Msk (0xffffffffu << HSMCI_FIFO_DATA_Pos) /**< \brief (HSMCI_FIFO[256]) Data to Read or Data to Write */ #define HSMCI_FIFO_DATA(value) ((HSMCI_FIFO_DATA_Msk & ((value) << HSMCI_FIFO_DATA_Pos))) /*@}*/ #ifdef __cplusplus } #endif #endif /* _SAM3XA_HSMCI_COMPONENT_ */