fb11e647
 vrobic
reseau statique a...
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
|
/*
* Copyright (C) 2014 Freie Universitรคt Berlin
* Copyright (C) 2015 Zolertia SL
*
* This file is subject to the terms and conditions of the GNU Lesser General
* Public License v2.1. See the file LICENSE in the top level directory for more
* details.
*/
/**
* @ingroup boards_remote
* @brief Support for the RE-Mote board Revision B
* @{
*
* @file
* @brief Board specific definitions for the RE-Mote board Revision B
*
* @author Hauke Petersen <hauke.petersen@fu-berlin.de>
* Antonio Lignan <alinan@zolertia.com>
*/
#ifndef BOARD_H_
#define BOARD_H_
#include "cpu.h"
#include "periph/gpio.h"
#include "periph/spi.h"
#include "board_common.h"
#ifdef __cplusplus
extern "C" {
#endif
/**
* @name LED pin definitions
* @{
*/
#define LED0_PIN GPIO_PD4
#define LED1_PIN GPIO_PB7
#define LED2_PIN GPIO_PB6
#define LED0_MASK (1 << 4)
#define LED1_MASK (1 << 7)
#define LED2_MASK (1 << 6)
#define LED0_ON (GPIO_D->DATA |= LED0_MASK)
#define LED0_OFF (GPIO_D->DATA &= ~LED0_MASK)
#define LED0_TOGGLE (GPIO_D->DATA ^= LED0_MASK)
#define LED1_ON (GPIO_B->DATA |= LED1_MASK)
#define LED1_OFF (GPIO_B->DATA &= ~LED1_MASK)
#define LED1_TOGGLE (GPIO_B->DATA ^= LED1_MASK)
#define LED2_ON (GPIO_B->DATA |= LED2_MASK)
#define LED2_OFF (GPIO_B->DATA &= ~LED2_MASK)
#define LED2_TOGGLE (GPIO_B->DATA ^= LED2_MASK)
/** @} */
/**
* @name User button pin definition
* @{
*/
#define BUTTON_GPIO GPIO_3_PIN
/** @} */
/**
* @name RF switch controlled by SW
* @brief Controls which RF interface goes to the RP-SMA external antenna
*
* These values configure the required pin to drive the RF antenna switch, to
* either enable the sub-1Ghz RF interface (power-up the CC1200) or the 2.4GHz
* RF interface of the CC2538, both alternatively routed to a RP-SMA connector
* to allow using an external antenna for both cases.
*
* Note it is also possible to enable both RF interfaces at the same time, by
* switching On the sub-1GHz RF interface, and placing an 0Ohm resistor (R19),
* to select between using a ceramic chip antenna (not mounted), or to connect
* and external antenna over a pigtail to the U.Fl connector (not mounted).
*
* RF switch state:
* - LOW: 2.4GHz RF interface on RP-SMA connector, CC1200 powered-off.
* - HIGH: Sub-1GHz RF interface on RP-SMA connector.
*
* @{
*/
#define RF_SWITCH_GPIO GPIO_PD2
#define RF_SWITCH_SUB_GHZ gpio_set(RF_SWITCH_GPIO)
#define RF_SWITCH_2_4_GHZ gpio_clear(RF_SWITCH_GPIO)
#define RF_SWITCH_TOGGLE gpio_toggle(RF_SWITCH_GPIO)
/** @} */
/**
* @name Power management enable pin
* @{
*/
#define SHUTDOWN_EN_GPIO GPIO_PD1
/** @} */
/**
* @name CC1200 SPI and pins definitions
* @{
*/
#define CC1200_SPI_DEV SSI0
#define CC1200_MOSI_GPIO GPIO_PB1
#define CC1200_MISO_GPIO GPIO_PB3
#define CC1200_SCLK_GPIO GPIO_PB2
#define CC1200_CSN_GPIO GPIO_PB5
#define CC1200_RESET_GPIO GPIO_PC7
#define CC1200_GPD0_GPIO GPIO_PB4
#define CC1200_GPD2_GPIO GPIO_PB0
/** @} */
#ifdef __cplusplus
} /* end extern "C" */
#endif
#endif /* BOARD_H_ */
/** @} */
|