8b438d9c
 root
Harmonisation ava...
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
|
/** \file
*
* This file contains special DoxyGen information for the generation of the main page and other special
* documentation pages. It is not a project source file.
*/
/** \mainpage Benito Arduino Programmer Project
*
* \section Sec_Compat Project Compatibility:
*
* The following list indicates what microcontrollers are compatible with this project.
*
* \li Series 7 USB AVRs (AT90USBxxx7)
* \li Series 6 USB AVRs (AT90USBxxx6)
* \li Series 4 USB AVRs (ATMEGAxxU4)
* \li Series 2 USB AVRs (AT90USBxx2, ATMEGAxxU2)
*
* \section Sec_Info USB Information:
*
* The following table gives a rundown of the USB utilization of this project.
*
* <table>
* <tr>
* <td><b>USB Mode:</b></td>
* <td>Device</td>
* </tr>
* <tr>
* <td><b>USB Class:</b></td>
* <td>Communications Device Class (CDC)</td>
* </tr>
* <tr>
* <td><b>USB Subclass:</b></td>
* <td>Abstract Control Model (ACM)</td>
* </tr>
* <tr>
* <td><b>Relevant Standards:</b></td>
* <td>USBIF CDC Class Standard \n
* Arduino Bootloader Specification</td>
* </tr>
* <tr>
* <td><b>Supported USB Speeds:</b></td>
* <td>Full Speed Mode</td>
* </tr>
* </table>
*
* \section Sec_Description Project Description:
*
* Firmware for a USB AVR powered programmer for Arduino boards using the official Arduino bootloader. This
* project acts like a regular USB to Serial bridge, except that asserting the DTR line will cause a pulse
* to appear on a given port pin, to control the target's /RESET pin.
*
* This is primarily designed to fit the Benito board from www.dorkbotpdx.org, but will suit all USB AVRs.
*
* After running this project for the first time on a new computer, you will need to supply the .INF file located
* in this project's directory as the device's driver when running under Windows. This will enable Windows to use
* its inbuilt CDC drivers, negating the need for custom drivers for the device. Other Operating Systems should
* automatically use their own inbuilt CDC-ACM drivers.
*
* \section Sec_Options Project Options
*
* The following defines can be found in this project, which can control the project behaviour when defined, or changed in value.
*
* <table>
* <tr>
* <th><b>Define Name:</b></th>
* <th><b>Location:</b></th>
* <th><b>Description:</b></th>
* </tr>
* <tr>
* <td>AVR_RESET_LINE_PORT</td>
* <td>AppConfig.h</td>
* <td>Indicates the PORT register of the pin used to generate the target /RESET line pulse.</td>
* </tr>
* <tr>
* <td>AVR_RESET_LINE_DDR</td>
* <td>AppConfig.h</td>
* <td>Indicates the DDR register of the pin used to generate the target /RESET line pulse.</td>
* </tr>
* <tr>
* <td>AVR_RESET_LINE_MASK</td>
* <td>AppConfig.h</td>
* <td>Indicates the mask of the pin used to generate the target /RESET line pulse.</td>
* </tr>
* <tr>
* <td>AVR_RESET_PULSE_MS</td>
* <td>AppConfig.h</td>
* <td>Pulse length in milliseconds for the target /RESET pulse.</td>
* </tr>
* <tr>
* <td>TX_RX_LED_PULSE_MS</td>
* <td>AppConfig.h</td>
* <td>Pulse length in milliseconds for the activity Tx/Rx LEDs.</td>
* </tr>
* <tr>
* <td>PING_PONG_LED_PULSE_MS</td>
* <td>AppConfig.h</td>
* <td>Pulse length in milliseconds for the enumeration LED ping-ponging between toggles.</td>
* </tr>
* <tr>
* <td>RECEIVE_BUFFER_FLUSH_MS</td>
* <td>AppConfig.h</td>
* <td>Period between flushings of received data buffer to the attached USB host.</td>
* </tr>
* </table>
*/
|