/* * Copyright (C) 2016 Freie Universität Berlin * 2016-2017 Inria * * This file is subject to the terms and conditions of the GNU Lesser * General Public License v2.1. See the file LICENSE in the top level * directory for more details. */ /** * @ingroup boards_arduino-mkr-common * @{ * * @file * @brief Configuration of CPU peripherals for Arduino MKR boards * * @author Thomas Eichinger * @author Hauke Petersen * @author Peter Kietzmann * @author Alexandre Abadie * @author Bumsik kim */ #ifndef PERIPH_CONF_H #define PERIPH_CONF_H #include "periph_cpu.h" #ifdef __cplusplus extern "C" { #endif /** * @name External oscillator and clock configuration * * For selection of the used CORECLOCK, we have implemented two choices: * * - usage of the PLL fed by the internal 8MHz oscillator divided by 8 * - usage of the internal 8MHz oscillator directly, divided by N if needed * * * The PLL option allows for the usage of a wider frequency range and a more * stable clock with less jitter. This is why we use this option as default. * * The target frequency is computed from the PLL multiplier and the PLL divisor. * Use the following formula to compute your values: * * CORECLOCK = ((PLL_MUL + 1) * 1MHz) / PLL_DIV * * NOTE: The PLL circuit does not run with less than 32MHz while the maximum PLL * frequency is 96MHz. So PLL_MULL must be between 31 and 95! * * * The internal Oscillator used directly can lead to a slightly better power * efficiency to the cost of a less stable clock. Use this option when you know * what you are doing! The actual core frequency is adjusted as follows: * * CORECLOCK = 8MHz / DIV * * NOTE: A core clock frequency below 1MHz is not recommended * * @{ */ #define CLOCK_USE_PLL (1) #if CLOCK_USE_PLL /* edit these values to adjust the PLL output frequency */ #define CLOCK_PLL_MUL (47U) /* must be >= 31 & <= 95 */ #define CLOCK_PLL_DIV (1U) /* adjust to your needs */ /* generate the actual used core clock frequency */ #define CLOCK_CORECLOCK (((CLOCK_PLL_MUL + 1) * 1000000U) / CLOCK_PLL_DIV) #else /* edit this value to your needs */ #define CLOCK_DIV (1U) /* generate the actual core clock frequency */ #define CLOCK_CORECLOCK (8000000 / CLOCK_DIV) #endif /** @} */ /** * @name Timer peripheral configuration * @{ */ #define TIMER_NUMOF (2U) #define TIMER_0_EN 1 #define TIMER_1_EN 1 /* Timer 0 configuration */ #define TIMER_0_DEV TC3->COUNT16 #define TIMER_0_CHANNELS 2 #define TIMER_0_MAX_VALUE (0xffff) #define TIMER_0_ISR isr_tc3 /* Timer 1 configuration */ #define TIMER_1_DEV TC4->COUNT32 #define TIMER_1_CHANNELS 2 #define TIMER_1_MAX_VALUE (0xffffffff) #define TIMER_1_ISR isr_tc4 /** @} */ /** * @name UART configuration * @{ */ static const uart_conf_t uart_config[] = { { .dev = &SERCOM5->USART, .rx_pin = GPIO_PIN(PB,23), /* ARDUINO_PIN_13, RX Pin */ .tx_pin = GPIO_PIN(PB,22), /* ARDUINO_PIN_14, TX Pin */ .mux = GPIO_MUX_D, .rx_pad = UART_PAD_RX_3, .tx_pad = UART_PAD_TX_2, .flags = UART_FLAG_NONE, .gclk_src = GCLK_CLKCTRL_GEN_GCLK0 } }; /* interrupt function name mapping */ #define UART_0_ISR isr_sercom5 #define UART_NUMOF (sizeof(uart_config) / sizeof(uart_config[0])) /** @} */ /** * @name PWM configuration * @{ */ #define PWM_0_EN 1 #define PWM_MAX_CHANNELS (2U) /* for compatibility with test application */ #define PWM_0_CHANNELS PWM_MAX_CHANNELS /* PWM device configuration */ static const pwm_conf_t pwm_config[] = { #if PWM_0_EN {TCC0, { /* GPIO pin, MUX value, TCC channel */ { GPIO_PIN(PA, 10), GPIO_MUX_F, 2 }, /* ~2 */ { GPIO_PIN(PA, 11), GPIO_MUX_F, 3 }, /* ~3 */ }} #endif }; /* number of devices that are actually defined */ #define PWM_NUMOF (sizeof(pwm_config) / sizeof(pwm_config[0])) /** @} */ /** * @name ADC configuration * @{ */ #define ADC_0_EN 1 #define ADC_MAX_CHANNELS 14 /* ADC 0 device configuration */ #define ADC_0_DEV ADC #define ADC_0_IRQ ADC_IRQn /* ADC 0 Default values */ #define ADC_0_CLK_SOURCE 0 /* GCLK_GENERATOR_0 */ #define ADC_0_PRESCALER ADC_CTRLB_PRESCALER_DIV512 #define ADC_0_NEG_INPUT ADC_INPUTCTRL_MUXNEG_GND #define ADC_0_GAIN_FACTOR_DEFAULT ADC_INPUTCTRL_GAIN_1X #define ADC_0_REF_DEFAULT ADC_REFCTRL_REFSEL_INT1V static const adc_conf_chan_t adc_channels[] = { /* port, pin, muxpos */ {GPIO_PIN(PA, 2), ADC_INPUTCTRL_MUXPOS_PIN0}, /* A0 */ {GPIO_PIN(PB, 2), ADC_INPUTCTRL_MUXPOS_PIN10}, /* A1 */ {GPIO_PIN(PB, 3), ADC_INPUTCTRL_MUXPOS_PIN11}, /* A2 */ {GPIO_PIN(PA, 4), ADC_INPUTCTRL_MUXPOS_PIN4}, /* A3 */ {GPIO_PIN(PA, 5), ADC_INPUTCTRL_MUXPOS_PIN5}, /* A4 */ {GPIO_PIN(PA, 6), ADC_INPUTCTRL_MUXPOS_PIN6}, /* A5 */ {GPIO_PIN(PA, 7), ADC_INPUTCTRL_MUXPOS_PIN7}, /* A6 */ }; #define ADC_0_CHANNELS (7U) #define ADC_NUMOF ADC_0_CHANNELS /** @} */ /** * @name SPI configuration * @{ */ static const spi_conf_t spi_config[] = { { .dev = &SERCOM1->SPI, .miso_pin = GPIO_PIN(PA, 19), /* ARDUINO_PIN_8, SERCOM1-MISO */ .mosi_pin = GPIO_PIN(PA, 16), /* ARDUINO_PIN_10, SERCOM1-MOSI */ .clk_pin = GPIO_PIN(PA, 17), /* ARDUINO_PIN_9, SERCOM1-SCK */ .miso_mux = GPIO_MUX_C, .mosi_mux = GPIO_MUX_C, .clk_mux = GPIO_MUX_C, .miso_pad = SPI_PAD_MISO_3, .mosi_pad = SPI_PAD_MOSI_0_SCK_1 }, { .dev = &SERCOM2->SPI, .miso_pin = GPIO_PIN(PA, 15), .mosi_pin = GPIO_PIN(PA, 12), .clk_pin = GPIO_PIN(PA, 13), .miso_mux = GPIO_MUX_C, .mosi_mux = GPIO_MUX_C, .clk_mux = GPIO_MUX_C, .miso_pad = SPI_PAD_MISO_3, .mosi_pad = SPI_PAD_MOSI_0_SCK_1 } }; #define SPI_NUMOF (sizeof(spi_config) / sizeof(spi_config[0])) /** @} */ /** * @name I2C configuration * @{ */ #define I2C_NUMOF (1U) #define I2C_0_EN 1 #define I2C_1_EN 0 #define I2C_2_EN 0 #define I2C_3_EN 0 #define I2C_IRQ_PRIO 1 #define I2C_0_DEV SERCOM0->I2CM #define I2C_0_IRQ SERCOM0_IRQn #define I2C_0_ISR isr_sercom0 /* I2C 0 GCLK */ #define I2C_0_GCLK_ID SERCOM0_GCLK_ID_CORE #define I2C_0_GCLK_ID_SLOW SERCOM0_GCLK_ID_SLOW /* I2C 0 pin configuration */ #define I2C_0_SDA GPIO_PIN(PA, 8) /* SERCOM0-SDA, on-board pull-up */ #define I2C_0_SCL GPIO_PIN(PA, 9) /* SERCOM0-SCL, on-board pull-up */ #define I2C_0_MUX GPIO_MUX_C /** @} */ /** * @name RTC configuration * @{ */ #define RTC_NUMOF (1U) #define RTC_DEV RTC->MODE2 /** @} */ /** * @name RTT configuration * @{ */ #define RTT_NUMOF (1U) #define RTT_DEV RTC->MODE0 #define RTT_IRQ RTC_IRQn #define RTT_IRQ_PRIO 10 #define RTT_ISR isr_rtc #define RTT_MAX_VALUE (0xffffffff) #define RTT_FREQUENCY (32768U) /* in Hz. For changes see `rtt.c` */ #define RTT_RUNSTDBY (1) /* Keep RTT running in sleep states */ /** @} */ #ifdef __cplusplus } #endif #endif /* PERIPH_CONF_H */ /** @} */