a752c7ab
 elopes
add first test an...
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
|
/*
* Copyright (C) 2014-2016 Freie Universitรคt Berlin
* 2015 Zolertia SL
*
* This file is subject to the terms and conditions of the GNU Lesser
* General Public License v2.1. See the file LICENSE in the top level
* directory for more details.
*/
/**
* @ingroup boards_remote-reva
* @{
*
* @file
* @brief Peripheral MCU configuration for the RE-Mote board revision A
*
* @author Hauke Petersen <hauke.petersen@fu-berlin.de>
* @author Antonio Lignan <alinan@zolertia.com>
* @author Sebastian Meiling <s@mlng.net>
*/
#ifndef PERIPH_CONF_H
#define PERIPH_CONF_H
#include "periph_common.h"
#ifdef __cplusplus
extern "C" {
#endif
/**
* @name UART configuration
* @{
*/
#define UART_NUMOF (1U)
#define UART_0_EN 1
#define UART_IRQ_PRIO 1
/* UART 0 device configuration */
#define UART_0_DEV UART0
#define UART_0_IRQ UART0_IRQn
#define UART_0_ISR isr_uart0
/* UART 0 pin configuration */
#define UART_0_TX_PIN GPIO_PA1
#define UART_0_RX_PIN GPIO_PA0
/** @} */
/**
* @name I2C configuration
* @{
*/
#define I2C_NUMOF 1
#define I2C_0_EN 1
#define I2C_IRQ_PRIO 1
/* I2C 0 device configuration */
#define I2C_0_DEV 0
#define I2C_0_IRQ I2C_IRQn
#define I2C_0_IRQ_HANDLER isr_i2c
#define I2C_0_SCL_PIN GPIO_PC3
#define I2C_0_SDA_PIN GPIO_PC2
static const i2c_conf_t i2c_config[I2C_NUMOF] = {
{
.scl_pin = I2C_0_SCL_PIN,
.sda_pin = I2C_0_SDA_PIN,
},
};
/** @} */
/**
* @brief Pre-calculated clock divider values based on a CLOCK_CORECLOCK (32MHz)
*
* Calculated with (CPSR * (SCR + 1)) = (CLOCK_CORECLOCK / bus_freq), where
* 1 < CPSR < 255 and
* 0 < SCR < 256
*/
static const spi_clk_conf_t spi_clk_config[] = {
{ .cpsr = 10, .scr = 31 }, /* 100khz */
{ .cpsr = 2, .scr = 39 }, /* 400khz */
{ .cpsr = 2, .scr = 15 }, /* 1MHz */
{ .cpsr = 2, .scr = 2 }, /* ~4.5MHz */
{ .cpsr = 2, .scr = 1 } /* ~10.7MHz */
};
/**
* @name SPI configuration
* @{
*/
static const spi_conf_t spi_config[] = {
{
.dev = SSI0,
.mosi_pin = GPIO_PB1,
.miso_pin = GPIO_PB3,
.sck_pin = GPIO_PB2,
.cs_pin = GPIO_PB5
},
{
.dev = SSI1,
.mosi_pin = GPIO_PC5,
.miso_pin = GPIO_PC6,
.sck_pin = GPIO_PC4,
.cs_pin = GPIO_PA7
}
};
#define SPI_NUMOF (sizeof(spi_config) / sizeof(spi_config[0]))
/** @} */
/**
* @name ADC configuration
* @{
*/
#define SOC_ADC_ADCCON_REF SOC_ADC_ADCCON_REF_AVDD5
static const adc_conf_t adc_config[] = {
GPIO_PIN(0, 5), /**< GPIO_PA5 = ADC1_PIN */
GPIO_PIN(0, 4), /**< GPIO_PA4 = ADC2_PIN */
/* voltage divider with 5/3 relationship to allow 5V sensors */
GPIO_PIN(0, 2), /**< GPIO_PA2 = ADC3_PIN */
};
#define ADC_NUMOF (sizeof(adc_config) / sizeof(adc_config[0]))
/** @} */
#ifdef __cplusplus
} /* end extern "C" */
#endif
#endif /* PERIPH_CONF_H */
/** @} */
|