a752c7ab
 elopes
add first test an...
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
|
/*
* Copyright (C) 2015 Freie Universitรคt Berlin
*
* This file is subject to the terms and conditions of the GNU Lesser
* General Public License v2.1. See the file LICENSE in the top level
* directory for more details.
*/
/**
* @ingroup cpu_ezr32wg
* @ingroup drivers_periph_uart
* @{
*
* @file
* @brief Low-level UART driver implementation
*
* @author Hauke Petersen <hauke.petersen@fu-berlin.de>
*
* @}
*/
#include "cpu.h"
#include "periph/uart.h"
#include "periph/gpio.h"
/**
* @brief Allocate memory to store the callback functions
*/
static uart_isr_ctx_t isr_ctx[UART_NUMOF];
/**
* @brief Get the pointer to the base register of the given UART device
*
* @param[in] dev UART device identifier
*
* @return base register address
*/
static inline USART_TypeDef *_uart(uart_t dev)
{
return uart_config[dev].dev;
}
int uart_init(uart_t dev, uint32_t baudrate, uart_rx_cb_t rx_cb, void *arg)
{
USART_TypeDef *uart;
/* check if device is valid and get base register address */
if (dev >= UART_NUMOF) {
return UART_NODEV;
}
uart = _uart(dev);
/* save interrupt callback context */
isr_ctx[dev].rx_cb = rx_cb;
isr_ctx[dev].arg = arg;
/* power on the device */
uart_poweron(dev);
/* put device in asynchronous mode @ 16x oversampling (default UART) */
uart->CTRL = 0;
/* configure to default 8N1 configuration */
uart->FRAME = (USART_FRAME_STOPBITS_ONE | USART_FRAME_DATABITS_EIGHT);
/* configure the baudrate - this looks more complicated than it is, we just
* multiply the HFPERCLK with 32 to cut down on rounding error when doing
* the division afterwards... */
uart->CLKDIV = (((CLOCK_HFPERCLK << 5) / (16 * baudrate) - 32) << 3);
/* configure the pins */
gpio_init(uart_config[dev].tx_pin, GPIO_OUT);
if (rx_cb) {
gpio_init(uart_config[dev].rx_pin, GPIO_IN);
uart->ROUTE = ((uart_config[dev].loc << _USART_ROUTE_LOCATION_SHIFT) |
USART_ROUTE_RXPEN | USART_ROUTE_TXPEN);
} else {
uart->ROUTE = ((uart_config[dev].loc << _USART_ROUTE_LOCATION_SHIFT) |
USART_ROUTE_TXPEN);
}
if (rx_cb) {
/* enable RX interrupt */
NVIC_EnableIRQ(uart_config[dev].irq);
NVIC_EnableIRQ(uart_config[dev].irq + 1);
uart->IEN |= USART_IEN_RXDATAV;
/* enable receiver and transmitter */
uart->CMD = USART_CMD_TXEN | USART_CMD_RXEN;
}
else {
uart->CMD = USART_CMD_TXEN;
}
return UART_OK;
}
void uart_write(uart_t dev, const uint8_t *data, size_t len)
{
for (size_t i = 0; i < len; i++) {
while (!(_uart(dev)->STATUS & USART_STATUS_TXBL));
_uart(dev)->TXDATA = data[i];
}
}
void uart_poweron(uart_t dev)
{
CMU->HFPERCLKEN0 |= (1 << uart_config[dev].cmu);
}
void uart_poweroff(uart_t dev)
{
CMU->HFPERCLKEN0 &= ~(1 << uart_config[dev].cmu);
}
static inline void rx_irq(int dev)
{
if (_uart(dev)->IF & USART_IF_RXDATAV) {
uint8_t data = (uint8_t)_uart(dev)->RXDATA;
isr_ctx[dev].rx_cb(isr_ctx[dev].arg, data);
}
cortexm_isr_end();
}
#ifdef UART_0_ISR_RX
void UART_0_ISR_RX(void)
{
rx_irq(0);
}
#endif
#ifdef UART_1_ISR_RX
void UART_1_ISR_RX(void)
{
rx_irq(1);
}
#endif
#ifdef UART_2_ISR_RX
void UART_2_ISR_RX(void)
{
rx_irq(2);
}
#endif
|