a752c7ab
elopes
add first test an...
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
|
Zolertia RE-Mote platform
============================================
The RE-Mote platform (Revision B) is a IoT Hardware development platform based
on TI's CC2538 system on chip (SoC), featuring an ARM Cortex-M3 with 512KB
flash, 32Kb RAM, double RF interface (Sub-1GHz CC1200 RF transceiver), and the
following goodies:
* ISM 2.4-GHz IEEE 802.15.4 & Zigbee compliant.
* ISM 868-, 915-, 920-, 950-MHz ISM/SRD Band.
* AES-128/256, SHA2 Hardware Encryption Engine.
* ECC-128/256, RSA Hardware Acceleration Engine for Secure Key Exchange.
* Power consumption down to 150nA using our shutdown mode.
* Flashing over BSL without requiring to press any button to enter bootloader mode.
* Built-in battery charger (500mA), Energy Harvesting and Solar Panels to be connected to standards LiPo batteries.
* Power input with wide range 3.7-16VDC.
Changes from Revision A
=========================
The list of changes are summarized in the [Wiki](https://github.com/Zolertia/Resources/wiki/RE-Mote:-Enhancements-from-Rev.A-to-Rev.B)
Port Features
=============
In terms of hardware support, the following drivers have been implemented:
* CC2538 System-on-Chip:
* UART
* Random number generator
* Low Power Modes
* General-Purpose Timers
* I2C/SPI library
* LEDs
* Buttons
* RF switch to programatically drive either 2.4GHz or sub-1GHz to a single RP-SMA
* RF 2.4GHz built-in in CC2538
And under work or pending at cc2538 base cpu:
* Built-in core temperature and battery sensor.
* CC1200 sub-1GHz radio interface.
* Micro-SD external storage.
* ADC
* USB (in CDC-ACM).
* uDMA Controller.
Requirements
============
* Toolchain to compile RIOT for the CC2538
* Drivers to enable your host to communicate with the platform
* Built-in BSL programming over USB using cc2538-bsl (included)
Install a Toolchain
-------------------
The toolchain used to build is arm-gcc, to check if it is currently installed run:
$ arm-none-eabi-gcc -v
Using built-in specs.
Target: arm-none-eabi
Configured with: /scratch/julian/lite-respin/eabi/src/gcc-4.3/configure
...
(skip)
...
Thread model: single
gcc version 4.3.2 (Sourcery G++ Lite 2008q3-66)
Else install from <https://launchpad.net/gcc-arm-embedded>
Drivers
-------
The RE-Mote features a CP2104 serial-to-USB module, the driver is commonly found in most OS, but if required it can be downloaded
from <https://www.silabs.com/products/mcu/Pages/USBtoUARTBridgeVCPDrivers.aspx>
### For the CC2538EM (USB CDC-ACM)
The RE-Mote has built-in support for USB 2.0 USB, Vendor and Product IDs are the following:
* VID 0x0451
* PID 0x16C8
On Linux and OS X this is straightforward, on windows you need to install the following driver:
<https://github.com/alignan/lufa/blob/remote-zongle/LUFA/CodeTemplates/WindowsINF/LUFA%20CDC-ACM.inf>
And replace the IDs accordingly.
### Device Enumerations
For the UART, serial line settings are 115200 8N1, no flow control.
Once all drivers have been installed correctly:
On windows, devices will appear as a virtual `COM` port.
On Linux, devices will appear under `/dev/`.
On OS X, `/dev/tty.SLAB_USBtoUARTx`.
On Linux:
* RE-Mote over CP2104: `ttyUSB0`
* RE-Mote over USB driver (in CDC-ACM): `ttyACMn` (n=0, 1, ....)
More Reading
============
1. [Zolertia RE-Mote website][remote-site]
2. [Zolertia Wiki page][zolertia-wiki]
2. [CC2538 System-on-Chip Solution for 2.4-GHz IEEE 802.15.4 and ZigBee applications (SWRU319B)][cc2538]
3. [CC1200 sub-1GHz RF transceiver][cc1200]
[remote-site]: http://www.zolertia.io/products "Zolertia RE-Mote"
[zolertia-wiki]: https://github.com/Zolertia/Resources/wiki
[cc1200]: http://www.ti.com/product/cc1200 "CC1200"
[cc2538]: http://www.ti.com/product/cc2538 "CC2538"
|