a752c7ab
 elopes
add first test an...
|
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
|
/*
* Copyright (C) 2017 Freie Universitรคt Berlin
*
* This file is subject to the terms and conditions of the GNU Lesser
* General Public License v2.1. See the file LICENSE in the top level
* directory for more details.
*/
/**
* @ingroup boards_nucleo144-f746
* @{
*
* @file
* @brief Peripheral MCU configuration for the nucleo144-f746 board
*
* @author Hauke Petersen <hauke.petersen@fu-berlin.de>
*/
#ifndef PERIPH_CONF_H
#define PERIPH_CONF_H
#include "periph_cpu.h"
#ifdef __cplusplus
extern "C" {
#endif
/**
* @name Clock settings
*
* @note This is auto-generated from
* `cpu/stm32_common/dist/clk_conf/clk_conf.c`
* @{
*/
/* give the target core clock (HCLK) frequency [in Hz],
* maximum: 216MHz */
#define CLOCK_CORECLOCK (216000000U)
/* 0: no external high speed crystal available
* else: actual crystal frequency [in Hz] */
#define CLOCK_HSE (8000000U)
/* 0: no external low speed crystal available,
* 1: external crystal available (always 32.768kHz) */
#define CLOCK_LSE (1)
/* peripheral clock setup */
#define CLOCK_AHB_DIV RCC_CFGR_HPRE_DIV1
#define CLOCK_AHB (CLOCK_CORECLOCK / 1)
#define CLOCK_APB1_DIV RCC_CFGR_PPRE1_DIV4 /* max 54MHz */
#define CLOCK_APB1 (CLOCK_CORECLOCK / 4)
#define CLOCK_APB2_DIV RCC_CFGR_PPRE2_DIV2 /* max 108MHz */
#define CLOCK_APB2 (CLOCK_CORECLOCK / 2)
/* Main PLL factors */
#define CLOCK_PLL_M (4)
#define CLOCK_PLL_N (216)
#define CLOCK_PLL_P (2)
#define CLOCK_PLL_Q (9)
/** @} */
/**
* @name Timer configuration
* @{
*/
static const timer_conf_t timer_config[] = {
{
.dev = TIM2,
.max = 0xffffffff,
.rcc_mask = RCC_APB1ENR_TIM2EN,
.bus = APB1,
.irqn = TIM2_IRQn
}
};
#define TIMER_0_ISR isr_tim2
#define TIMER_NUMOF (sizeof(timer_config) / sizeof(timer_config[0]))
/** @} */
/**
* @name UART configuration
* @{
*/
static const uart_conf_t uart_config[] = {
{
.dev = USART3,
.rcc_mask = RCC_APB1ENR_USART3EN,
.rx_pin = GPIO_PIN(PORT_D, 9),
.tx_pin = GPIO_PIN(PORT_D, 8),
.rx_af = GPIO_AF7,
.tx_af = GPIO_AF7,
.bus = APB1,
.irqn = USART3_IRQn,
#ifdef UART_USE_DMA
.dma_stream = 6,
.dma_chan = 4
#endif
},
{
.dev = USART6,
.rcc_mask = RCC_APB2ENR_USART6EN,
.rx_pin = GPIO_PIN(PORT_G, 9),
.tx_pin = GPIO_PIN(PORT_G, 14),
.rx_af = GPIO_AF8,
.tx_af = GPIO_AF8,
.bus = APB2,
.irqn = USART6_IRQn,
#ifdef UART_USE_DMA
.dma_stream = 5,
.dma_chan = 4
#endif
},
{
.dev = USART2,
.rcc_mask = RCC_APB1ENR_USART2EN,
.rx_pin = GPIO_PIN(PORT_D, 6),
.tx_pin = GPIO_PIN(PORT_D, 5),
.rx_af = GPIO_AF7,
.tx_af = GPIO_AF7,
.bus = APB1,
.irqn = USART2_IRQn,
#ifdef UART_USE_DMA
.dma_stream = 4,
.dma_chan = 4
#endif
}
};
#define UART_0_ISR (isr_usart3)
#define UART_0_DMA_ISR (isr_dma1_stream6)
#define UART_1_ISR (isr_usart6)
#define UART_1_DMA_ISR (isr_dma1_stream5)
#define UART_2_ISR (isr_usart2)
#define UART_2_DMA_ISR (isr_dma1_stream4)
#define UART_NUMOF (sizeof(uart_config) / sizeof(uart_config[0]))
/** @} */
/**
* @name ADC configuration
* @{
*/
#define ADC_NUMOF (0)
/** @} */
#ifdef __cplusplus
}
#endif
#endif /* PERIPH_CONF_H */
/** @} */
|