/*
   * Copyright (C) 2015 Loci Controls Inc.
   *
   * This file is subject to the terms and conditions of the GNU Lesser
   * General Public License v2.1. See the file LICENSE in the top level
   * directory for more details.
   */
  
  /**
   * @ingroup     cpu_cc2538
   * @ingroup     drivers_periph
   * @{
   *
   * @file
   * @brief       Low-level I2C driver implementation
   *
   * @author      Ian Martin <ian@locicontrols.com>
   *
   * @}
   */
  
  #include <assert.h>
  #include <stdbool.h>
  #include <stdio.h>
  #include <stdint.h>
  
  #include "mutex.h"
  #include "cpu.h"
  #include "periph/i2c.h"
  #include "thread.h"
  #ifdef MODULE_XTIMER
  #include "xtimer.h"
  #endif
  #include "timex.h" /* for US_PER_SEC */
  
  #define ENABLE_DEBUG (0)
  #include "debug.h"
  
  /* guard this file in case no I2C device is defined */
  #if I2C_NUMOF
  
  #ifndef I2C_0_SCL_PIN
  #define I2C_0_SCL_PIN i2c_config[I2C_0].scl_pin
  #endif
  
  #ifndef I2C_0_SDA_PIN
  #define I2C_0_SDA_PIN i2c_config[I2C_0].sda_pin
  #endif
  
  #undef BIT
  #define BIT(n)     ( 1 << (n) )
  
  /* Standard I2C Parameters */
  #define DATA_BITS  8
  #define ACK_BITS   1
  
  /* I2CM_DR Bits */
  #define RS         BIT(0)
  
  /* I2CM_CTRL Bits */
  #define ACK        BIT(3)
  #define STOP       BIT(2)
  #define START      BIT(1)
  #define RUN        BIT(0)
  
  /* I2CM_STAT Bits */
  #define BUSBSY     BIT(6)
  #define IDLE       BIT(5)
  #define ARBLST     BIT(4)
  #define DATACK     BIT(3)
  #define ADRACK     BIT(2)
  #define ERROR      BIT(1)
  #define BUSY       BIT(0)
  
  /* I2CM_CR Bits */
  #define SFE        BIT(5)
  #define MFE        BIT(4)
  #define LPBK       BIT(0)
  
  #define ANY_ERROR  (ARBLST | DATACK | ADRACK | ERROR)
  
  #define SCL_LP     6 /**< SCL Low Period (fixed at 6). */
  #define SCL_HP     4 /**< SCL High Period (fixed at 4). */
  
  static mutex_t mutex = MUTEX_INIT;
  static mutex_t i2c_wait_mutex = MUTEX_INIT;
  static uint32_t speed_hz;
  static uint32_t scl_delay;
  
  #define bus_quiet()            ( cc2538_gpio_read(I2C_0_SCL_PIN) && cc2538_gpio_read(I2C_0_SDA_PIN) )
  #define WARN_IF(cond) \
          if (cond) { \
              DEBUG("%s at %s:%u\n", #cond, RIOT_FILE_NOPATH, __LINE__); \
          }
  
  void cc2538_i2c_init_master(uint32_t speed_hz);
  
  static void i2cm_ctrl_write(uint_fast8_t value) {
      WARN_IF(I2CM_STAT & BUSY);
      I2CM_CTRL = value;
  }
  
  static void assert_scl(void) {
      cc2538_gpio_clear(I2C_0_SCL_PIN);
      IOC_PXX_OVER[I2C_0_SCL_PIN] |= IOC_OVERRIDE_OE;
      gpio_dir_output(I2C_0_SCL_PIN);
      gpio_software_control(I2C_0_SCL_PIN);
  }
  
  static void release_scl(void) {
      IOC_PXX_OVER[I2C_0_SCL_PIN] &= ~(IOC_OVERRIDE_OE | IOC_OVERRIDE_PDE);
      gpio_dir_input(I2C_0_SCL_PIN);
      gpio_software_control(I2C_0_SCL_PIN);
  }
  
  static void release_sda(void) {
      IOC_PXX_OVER[I2C_0_SDA_PIN] &= ~(IOC_OVERRIDE_OE | IOC_OVERRIDE_PDE);
      gpio_dir_input(I2C_0_SDA_PIN);
      gpio_software_control(I2C_0_SDA_PIN);
  }
  
  static void recover_i2c_bus(void) {
      /* Switch to software GPIO mode for bus recovery */
      release_sda();
      release_scl();
  
      if (!bus_quiet()) {
          const uint_fast8_t try_limit = 200;
          uint_fast8_t n;
          for (n = 0; n < try_limit; n++) {
              if (bus_quiet()) {
                  DEBUG("%s(): SDA released after%4u SCL pulses.\n", __FUNCTION__, n);
                  break;
              }
  
              assert_scl();
  
  #ifdef MODULE_XTIMER
              xtimer_usleep(scl_delay);
  #else
              thread_yield();
  #endif
  
              release_scl();
  
  #ifdef MODULE_XTIMER
              xtimer_usleep(scl_delay);
  #else
              thread_yield();
  #endif
          }
  
          if (n >= try_limit) {
              DEBUG("%s(): Failed to release SDA after%4u SCL pulses.\n", __FUNCTION__, n);
          }
      }
  
      /* Return to hardware mode for the I2C pins */
      gpio_hardware_control(I2C_0_SCL_PIN);
      gpio_hardware_control(I2C_0_SDA_PIN);
  }
  
  #ifdef MODULE_XTIMER
  static void _timer_cb(void *arg)
  {
      mutex_unlock(&i2c_wait_mutex);
  }
  #endif
  
  static uint_fast8_t i2c_ctrl_blocking(uint_fast8_t flags)
  {
  #ifdef MODULE_XTIMER
      const unsigned int xtimer_timeout = 3 * (DATA_BITS + ACK_BITS) * US_PER_SEC / speed_hz;
  #endif
  
      mutex_trylock(&i2c_wait_mutex);
  
      assert(I2CM_IMR & 1);
      i2cm_ctrl_write(flags);
  
  #ifdef MODULE_XTIMER
      /* Set a timeout at double the expected time to transmit a byte: */
      xtimer_t xtimer = { .callback = _timer_cb, .arg = NULL };
      xtimer_set(&xtimer, xtimer_timeout);
  #endif
  
      mutex_lock(&i2c_wait_mutex);
  
  #ifdef MODULE_XTIMER
      xtimer_remove(&xtimer);
  #endif
  
      if (I2CM_STAT & BUSY) {
          /* If the controller is still busy, it probably will be forever */
  #ifdef MODULE_XTIMER
          DEBUG("Master is still BUSY after %u usec. Resetting.\n", xtimer_timeout);
  #endif
          cc2538_i2c_init_master(speed_hz);
      }
  
      WARN_IF(I2CM_STAT & BUSY);
  
      return I2CM_STAT;
  }
  
  void isr_i2c(void)
  {
      /* Clear the interrupt flag */
      I2CM_ICR = 1;
  
      /* Unlock the wait mutex */
      mutex_unlock(&i2c_wait_mutex);
  
      cortexm_isr_end();
  }
  
  void cc2538_i2c_init_master(uint32_t speed_hz)
  {
      SYS_CTRL_RCGCI2C |= 1; /**< Enable the I2C0 clock. */
      SYS_CTRL_SCGCI2C |= 1; /**< Enable the I2C0 clock. */
      SYS_CTRL_DCGCI2C |= 1; /**< Enable the I2C0 clock. */
  
      /* Reset I2C peripheral */
      SYS_CTRL_SRI2C |= 1;
  
  #ifdef MODULE_XTIMER
      xtimer_usleep(50);
  #else
      thread_yield();
  #endif
  
      SYS_CTRL_SRI2C &= ~1;
  
      /* Clear all pin override flags except PUE (Pull-Up Enable) */
      IOC_PXX_OVER[I2C_0_SCL_PIN] &= IOC_OVERRIDE_PUE;
      IOC_PXX_OVER[I2C_0_SDA_PIN] &= IOC_OVERRIDE_PUE;
  
      IOC_PXX_SEL[I2C_0_SCL_PIN] = I2C_CMSSCL;
      IOC_PXX_SEL[I2C_0_SDA_PIN] = I2C_CMSSDA;
  
      IOC_I2CMSSCL = I2C_0_SCL_PIN;
      IOC_I2CMSSDA = I2C_0_SDA_PIN;
  
      gpio_hardware_control(I2C_0_SCL_PIN);
      gpio_hardware_control(I2C_0_SDA_PIN);
  
      /* Initialize the I2C master by setting the Master Function Enable bit */
      I2CM_CR |= MFE;
  
      /* Set the SCL clock speed */
      uint32_t ps = sys_clock_freq();
      uint32_t denom = 2 * (SCL_LP + SCL_HP) * speed_hz;
      ps += denom / 2;
      ps /= denom;
      I2CM_TPR = ps - 1;
  
      /* Enable I2C master interrupts */
      NVIC_SetPriority(I2C_IRQn, I2C_IRQ_PRIO);
      NVIC_EnableIRQ(I2C_IRQn);
  
      i2cm_ctrl_write(STOP);
  
      /* Enable I2C master interrupts */
      I2CM_IMR = 1;
  }
  
  int i2c_init_master(i2c_t dev, i2c_speed_t speed)
  {
      switch (dev) {
  #if I2C_0_EN
          case I2C_0:
              break;
  #endif
          default:
              return -1;
      }
  
      switch (speed) {
          case I2C_SPEED_LOW:
              speed_hz = 10000;
              break;
  
          case I2C_SPEED_NORMAL:
              speed_hz = 100000;
              break;
  
          case I2C_SPEED_FAST:
              speed_hz = 400000;
              break;
  
          case I2C_SPEED_FAST_PLUS:
              speed_hz = 1000000;
              break;
  
          case I2C_SPEED_HIGH:
              speed_hz = 3400000;
              break;
  
          default:
              return -2;
      }
  
      cc2538_i2c_init_master(speed_hz);
  
      /* Pre-compute an SCL delay in microseconds */
      scl_delay = US_PER_SEC;
      scl_delay += speed_hz;
      scl_delay /= 2 * speed_hz;
  
      return 0;
  }
  
  int i2c_init_slave(i2c_t dev, uint8_t address)
  {
      /* Slave mode is not (yet) supported. */
      return -1;
  }
  
  int i2c_acquire(i2c_t dev)
  {
      if (dev == I2C_0) {
          mutex_lock(&mutex);
          return 0;
      }
      else {
          return -1;
      }
  }
  
  int i2c_release(i2c_t dev)
  {
      if (dev == I2C_0) {
          mutex_unlock(&mutex);
          return 0;
      }
      else {
          return -1;
      }
  }
  
  static bool i2c_busy(void) {
      if (I2CM_STAT & BUSY) {
          cc2538_i2c_init_master(speed_hz);
          return (I2CM_STAT & BUSY) != 0;
      }
  
      return false;
  }
  
  int i2c_read_byte(i2c_t dev, uint8_t address, void *data)
  {
      return i2c_read_bytes(dev, address, data, 1);
  }
  
  static int i2c_read_bytes_dumb(uint8_t address, uint8_t *data, int length)
  {
      int n = 0;
      uint_fast8_t stat;
  
      switch (length) {
          case 0:
              break;
  
          case 1:
              if (i2c_busy()) {
                  break;
              }
  
              I2CM_SA = (address << 1) | RS;
              stat = i2c_ctrl_blocking(STOP | START | RUN);
              if (stat & ANY_ERROR) {
                  break;
              }
              data[n] = I2CM_DR;
              n++;
              break;
  
          default:
              if (i2c_busy()) {
                  break;
              }
  
              I2CM_SA = (address << 1) | RS;
              stat = i2c_ctrl_blocking(ACK | START | RUN);
  
              if (stat & ARBLST) {
                   break;
              }
              else if (stat & ANY_ERROR) {
                  i2cm_ctrl_write(STOP);
                  break;
              }
  
              data[n] = I2CM_DR;
              n++;
  
              while (n < length) {
                  stat = i2c_ctrl_blocking((n < length - 1) ? (ACK | RUN) : (STOP | RUN));
  
                  if (stat & ARBLST) {
                       break;
                  }
                  else if (stat & ANY_ERROR) {
                      i2cm_ctrl_write(STOP);
                      break;
                  }
  
                  data[n] = I2CM_DR;
                  n++;
              }
  
              break;
      }
  
      return n;
  }
  
  int i2c_read_bytes(i2c_t dev, uint8_t address, void *data, int length)
  {
      switch (dev) {
  #if I2C_0_EN
          case I2C_0:
              break;
  #endif
  
          default:
              return -1;
      }
  
      WARN_IF(I2CM_STAT & BUSY);
  
      if ( (length <= 0) || i2c_busy() ) {
          return 0;
      }
  
      WARN_IF(I2CM_STAT & BUSBSY);
  
      if (I2CM_STAT & BUSBSY) {
          recover_i2c_bus();
  
          if (I2CM_STAT & BUSBSY) {
              return 0;
          }
      }
  
      return i2c_read_bytes_dumb(address, data, length);
  }
  
  int i2c_read_reg(i2c_t dev, uint8_t address, uint8_t reg, void *data)
  {
      return i2c_read_regs(dev, address, reg, data, 1);
  }
  
  int i2c_read_regs(i2c_t dev, uint8_t address, uint8_t reg, void *data, int length)
  {
      uint_fast8_t stat;
  
      if (dev != I2C_0) {
          return -1;
      }
  
      /* Transmit reg byte to slave */
      if (i2c_busy()) {
          return 0;
      }
  
      WARN_IF(I2CM_STAT & BUSBSY);
  
      if (I2CM_STAT & BUSBSY) {
          recover_i2c_bus();
  
          if (I2CM_STAT & BUSBSY) {
              return 0;
          }
      }
  
      I2CM_SA = address << 1;
      I2CM_DR = reg;
      stat = i2c_ctrl_blocking(START | RUN);
  
      if (stat & ARBLST) {
          return 0;
      }
      else if (stat & ANY_ERROR) {
          i2cm_ctrl_write(STOP);
          return 0;
      }
      else {
          /* Receive data from slave */
          return i2c_read_bytes_dumb(address, data, length);
      }
  }
  
  int i2c_write_byte(i2c_t dev, uint8_t address, uint8_t data)
  {
      return i2c_write_bytes(dev, address, &data, 1);
  }
  
  int i2c_write_bytes(i2c_t dev, uint8_t address, const void *data, int length)
  {
      int n = 0;
      const uint8_t *my_data = data;
  
      if (dev != I2C_0) {
          return -1;
      }
  
      WARN_IF(I2CM_STAT & BUSBSY);
  
      if (I2CM_STAT & BUSBSY) {
          recover_i2c_bus();
  
          if (I2CM_STAT & BUSBSY) {
              return 0;
          }
      }
  
      I2CM_SA = address << 1;
      uint_fast8_t flags = START | RUN;
  
      for (n = 0; n < length; n++) {
          if (n >= length - 1) flags |= STOP;
          WARN_IF(I2CM_STAT & BUSY);
          I2CM_DR = my_data[n];
          i2c_ctrl_blocking(flags);
  
          WARN_IF(I2CM_STAT & ARBLST);
          WARN_IF(I2CM_STAT & DATACK);
          WARN_IF(I2CM_STAT & ADRACK);
          WARN_IF(I2CM_STAT & ERROR);
  
          if (I2CM_STAT & ARBLST) {
               break;
          }
          else if (I2CM_STAT & ANY_ERROR) {
              i2cm_ctrl_write(STOP);
              break;
          }
  
          flags = RUN;
      }
  
          if (n < length) {
              DEBUG("%s(%u, %p, %u): %u/%u bytes delivered.\n",
                    __FUNCTION__, address, (void *)my_data, length, n, length);
          }
  
      return n;
  }
  
  int i2c_write_reg(i2c_t dev, uint8_t address, uint8_t reg, uint8_t data)
  {
      return i2c_write_regs(dev, address, reg, &data, 1);
  }
  
  int i2c_write_regs(i2c_t dev, uint8_t address, uint8_t reg, const void *data, int length)
  {
      uint_fast8_t stat;
      const uint8_t *my_data = data;
  
      if (dev != I2C_0) {
          return -1;
      }
  
      /* Transmit reg byte to slave */
      if (i2c_busy()) {
          return 0;
      }
  
      WARN_IF(I2CM_STAT & BUSBSY);
  
      if (I2CM_STAT & BUSBSY) {
          recover_i2c_bus();
  
          if (I2CM_STAT & BUSBSY) {
              return 0;
          }
      }
  
      I2CM_SA = address << 1;
      I2CM_DR = reg;
  
      uint_fast8_t flags = (length > 0)? (START | RUN) : (STOP | START | RUN);
      stat = i2c_ctrl_blocking(flags);
  
      if (stat & ARBLST) {
          return 0;
      }
      else if (stat & ANY_ERROR) {
          i2cm_ctrl_write(STOP);
          return 0;
      }
      else {
          /* Transmit data to slave */
          int n = 0;
  
          flags &= ~START;
  
          for (n = 0; n < length; n++) {
              if (n >= length - 1) flags |= STOP;
              WARN_IF(I2CM_STAT & BUSY);
              I2CM_DR = my_data[n];
  
              i2c_ctrl_blocking(flags);
  
              WARN_IF(I2CM_STAT & ARBLST);
              WARN_IF(I2CM_STAT & DATACK);
              WARN_IF(I2CM_STAT & ADRACK);
              WARN_IF(I2CM_STAT & ERROR);
  
              if (I2CM_STAT & ARBLST) {
                   break;
              }
              else if (I2CM_STAT & ANY_ERROR) {
                  i2cm_ctrl_write(STOP);
                  break;
              }
          }
  
          if (n < length) {
              DEBUG(
                  "%s(%u, %u, %u, %p, %u): %u/%u bytes delivered.\n",
                  __FUNCTION__,
                  dev,
                  address,
                  reg,
                  data,
                  length,
                  n,
                  length
              );
          }
  
          return n;
      }
  }
  
  void i2c_poweron(i2c_t dev)
  {
      if (dev == I2C_0) {
          SYS_CTRL_RCGCI2C |= 1; /**< Enable the I2C0 clock. */
          SYS_CTRL_SCGCI2C |= 1; /**< Enable the I2C0 clock. */
          SYS_CTRL_DCGCI2C |= 1; /**< Enable the I2C0 clock. */
  
          I2CM_CR |= MFE;        /**< I2C master function enable. */
  
          /* Enable I2C master interrupts */
          I2CM_IMR = 1;
      }
  }
  
  void i2c_poweroff(i2c_t dev)
  {
      if (dev == I2C_0) {
          /* Disable I2C master interrupts */
          I2CM_IMR = 0;
          NVIC_DisableIRQ(I2C_IRQn);
  
          I2CM_CR &= ~MFE;        /**< I2C master function enable. */
  
          SYS_CTRL_RCGCI2C &= ~1; /**< Disable the I2C0 clock. */
          SYS_CTRL_SCGCI2C &= ~1; /**< Disable the I2C0 clock. */
          SYS_CTRL_DCGCI2C &= ~1; /**< Disable the I2C0 clock. */
      }
  }
  
  #endif /* I2C_NUMOF */